Icom IC-7600 Instruction Manual - Page 160

12 CONTROL COMMAND 153 D Command table (continued) Cmd. Sub cmd. Data Description 15 15 0000 to Read VD meter 0255 (0152=10 V, 0181=13 V, 0212=16 V) 16 0000 to Read ID meter 0255 (0000=0 A, 0097=10 A, 0241=25 A) 16 02 00 Preamp OFF 01 Preamp 1 ON 02 Preamp 2 ON 12 00 AGC FAST selection 01 AGC MID selection 02 AGC SLOW selection 22 00 Noise blanker OFF 01 Noise blanker ON 32 00 Audio peak filter OFF 01 Audio peak filter WIDE ON (320 Hz is selected when SHARP APF is set) 02 Audio peak filter MID ON (160 Hz is selected when SHARP APF is set) 03 Audio peak filter NAR ON (80 Hz is selected when SHARP APF is set) 40 00 Noise reduction OFF 01 Noise reduction ON 41 00 Auto notch function OFF 01 Auto notch function ON 42 00 Repeater tone OFF 01 Repeater tone ON 43 00 Tone squelch OFF 01 Tone squelch ON 44 00 Speech compressor OFF 01 Speech compressor ON 45 00 Monitor function OFF 01 Monitor function ON 46 00 VOX function OFF 01 VOX function ON 47 00 BK-IN function OFF 01 Semi BK-IN function ON 02 Full BK-IN function ON 48 00 Manual notch function OFF 01 Manual notch function ON 4F 00 Twin peak filter OFF 01 Twin peak filter ON 50 00 Dial lock function OFF 01 Dial lock function ON 19 00 Read the transceiver ID 1A 00 see p. 159 Send/read memory contents 01 see p. 157 Send/read band stacking register contents 02 see p. 157 Send/read memory keyer contents 03 00 to 49 Send/read the selected filter width (SSB, CW, PSK: 00=50 Hz, 40=3600 Hz; RTTY: 00=50 Hz, 31=2700 Hz; AM: 00=200 Hz, 49=10 kHz) 04 00 to 13 Send/read the selected AGC time constant (00=OFF, 01=0.1/0.3 sec., 13=6.0/8.0 sec.) 05 0001 see p. 120 Send/read SSB RX HPF/LPF 0002 00 to 10 Send/read SSB RX Tone (Bass) level (00=-5, 10=+5) 0003 00 to 10 Send/read SSB RX Tone (Treble) level (00=-5, 10=+5) 0004 see p. 120 Send/read AM RX HPF/LPF 0005 00 to 10 Send/read AM RX tone (Bass) level (00=-5, 10=+5) 0006 00 to 10 Send/read AM RX Tone (Treble) level (00=-5, 10=+5) 0007 see p. 120 Send/read FM RX HPF/LPF 0008 00 to 10 Send/read FM RX tone (Bass) level (00=-5, 10=+5) 0009 00 to 10 Send/read FM RX Tone (Treble) level (00=-5, 10=+5) 0010 see p. 121 Send/read CW RX HPF/LPF 0011 see p. 121 Send/read RTTY RX HPF/LPF 0012 see p. 121 Send/read PSK RX HPF/LPF 0013 00 to 10 Send/read SSB TX Tone (Bass) level (00=-5, 10=+5) 0014 00 to 10 Send/read SSB TX Tone (Treble) level (00=-5, 10=+5) Cmd. Sub cmd. Data Description 1A 05 0015 00 to 10 Send/read AM TX Tone (Bass) level (00=-5, 10=+5) 0016 00 to 10 Send/read AM TX Tone (Treble) level (00=-5, 10=+5) 0017 00 to 10 Send/read FM TX Tone (Bass) level (00=-5, 10=+5) 0018 00 to 10 Send/read FM TX Tone (Treble) level (00=-5, 10=+5) 0019 see p. 122 Send/read SSB TX bandwidth for WIDE 0020 see p. 122 Send/read SSB TX bandwidth for MID. 0021 see p. 122 Send/read SSB TX bandwidth for NARROW 0022 0000 to Send/read DRIVE gain 0255 (0000=0%, 0255=100%) 0023 0000 to Send/read speech level 0255 (0000=0%, 0255=100%) 0024 0000 to Send/read CW sidetone level 0255 (0000=0%, 0255=100%) 0025 00 CW sidetone level limit OFF 01 CW sidetone level limit ON 0026 0000 to Send/read beep level 0255 (0000=0%, 0255=100%) 0027 00 Beep level limit OFF 01 Beep level limit ON 0028 00 Squelch mute effect OFF (squelch is fixed open) for audio output from USB-B connector 01 Squelch mute effect ON for audio output from USB-B connector 0029 0000 to Send/read modulation level for audio input to 0255 USB-B connector (0000=0%, 0255=100%) 0030 00 [MIC] selection for MOD input connector during DATA OFF 01 [ACC] selection for MOD input connector during DATA OFF 02 Both [MIC] and [ACC] selection for MOD input connector during DATA OFF 03 [USB] selection for MOD input connector during DATA OFF 0031 00 [MIC] selection for MOD input connector during DATA1 01 [ACC] selection for MOD input connector during DATA1 02 Both [MIC] and [ACC] selection for MOD input connector during DATA1 03 [USB] selection for MOD input connector during DATA1 0032 00 [MIC] selection for MOD input connector during DATA2 01 [ACC] selection for MOD input connector during DATA2 02 Both [MIC] and [ACC] selection for MOD input connector during DATA2 03 [USB] selection for MOD input connector during DATA2 0033 00 [MIC] selection for MOD input connector during DATA3 01 [ACC] selection for MOD input connector during DATA3 02 Both [MIC] and [ACC] selection for MOD input connector during DATA3 03 [USB] selection for MOD input connector during DATA3 0034 00 Lead selection for SEND relay type 01 MOS-FET selection for SEND relay type 0035 00 Auto selection for external meter output 01 S (receiving signal strength) selection for external meter output 02 Po (RF power) selection for external meter selection 03 SWR selection for external meter output 04 ALC selection for external meter output 05 COMP selection for external meter output 06 Vd selection for external meter output 07 Id selection for external meter output 0036 0000 to Send/read external meter output level 0255 (see p. 125)