Icom IC-7600 Instruction Manual - Page 16
Audio Peak Filter/twin Peak Filter, Vfo/memory Switch [vfo/memo] - computer program
View all Icom IC-7600 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 16 highlights
1 PANEL DESCRIPTION ■ Front panel (continued) $6 $7 $8 $9 %0 %1 TIMER POWER HF/50MHz TRANSCEIVER TRANSMIT PHONES TUNER MONITOR BAL NR ELEC-KEY NB NR AF RF/SQL MIC MIC GAIN RF POWER BK-IN DELAY KEY SPEED TX RX SPLIT LOCK SPLIT 1.8 1 3.5 2 7 3 10 4 14 5 18 6 DUAL WATCH 21 7 24 8 28 9 CHANGE GENE 50 0 F-INP ENT MAIN /SUB M.SCOPE MP-W MW MP-R VFO/MEMO XFC TS TWIN-PBT PBT-CLR NOTCH APF/TPF NOTCH CW PITCH F-1 SSB F-2 F-3 F-4 F-5 F-6 AUTO TUNE CW RTTY/PSK AM / FM FILTER EXIT/SET REC PLAY VOICE MEMORY RIT ӠTX CLEAR RIT/ӠTX SPEECH LOCK %2 %3 %4 %5 $6 M EMORY UP/DOWN SWITCHES p. 99) ➥ Push to select the desired memory channel. • Memory channels can be selected both in VFO and memory modes. ➥ Push to select the desired memory channel directly after pushing [F-INP ENT] and a memory channel number. $7 MEMORY WRITE SWITCH [MW] (p. 101) Stores the selected readout frequency and operat- ing mode into the displayed memory channel when pushed and held for 1 sec. • This function is available both in VFO and memory modes. $8 MEMO PAD-WRITE SWITCH [MP-W] (p. 104) Programs the displayed readout frequency and op- erating mode into a memo pad. • The 5 most recent entries remain in memo pads. • The memo pad capacity can be expanded from 5 to 10 in others set mode. (p. 132) $9 MEMO PAD-READ SWITCH [MP-R] (p. 104) Each push calls up a frequency and operating mode in a memo pad. The 5 (or 10) most recently programmed frequencies and operating modes can be recalled, starting from the most recent. • The memo pad capacity can be expanded from 5 to 10 in others set mode. (p. 132) %0 VFO/MEMORY SWITCH [VFO/MEMO] ➥ Switches the selected readout operating mode between the VFO and memory when pushed. (pgs. 26, 99) ➥ Transfers the memory contents to VFO when pushed and held for 1 sec. (p. 102) %1 QUICK TUNING SWITCH [TS] ➥ Turns the quick tuning step ON and OFF. (p. 29) • While the quick tuning indicator, "Z," is displayed above the frequency indication, the frequency can be changed in programmed kHz steps. • 0.1, 1, 5, 9, 10, 12.5, 20 and 25 kHz steps are available for each operating mode independently. ➥ When the quick tuning step is ON, push and hold for 1 sec. to enter quick tuning step set mode. (p. 29) ➥ When the quick tuning step is OFF, push and hold for 1 sec. to turn the 1 Hz tuning step ON and OFF. (p. 30) %2 A UDIO PEAK FILTER/TWIN PEAK FILTER SWITCH [APF/TPF] During CW mode operation (p. 39) ➥ Push to turn the audio peak filter ON and OFF. • " " appears when audio peak filter is in use. ➥ When the audio peak filter is ON, push and hold for 1 sec. to select the APF passband width from WIDE, MID and NAR or from 320, 160 and 80 Hz depending on APF type setting (SOFT or SHARP). During RTTY mode operation (p. 47) ➥ Push to turn the twin peak filter ON and OFF. • " " appears when twin peak filter is in use. • The indicator on this switch lights green when the function is activated.