Icom IC-7600 Instruction Manual - Page 167

13 SPECIFICATIONS AND OPTIONS ■ General • Frequency coverage : (unit: MHz) Receive 0.030-60.000*1*2 Transmit 1.800-1.999*2, 3.500-3.999*2, 5.33050*3, 5.34650*3, 5.36650*3, 5.37150*3, 5.40350*3, 7.000-7.300*2, 10.100-10.150*2, 14.000-14.350*2, 18.068-18.168*2, 21.000-21.450*2, 24.890-24.990*2, 28.000-29.700*2, 50.000-54.000*2 *1Some frequency bands are not guaranteed. *2Depending on version. *3USA version only. • Mode : USB, LSB, CW, RTTY, PSK, AM, FM • No. of memory channels : 101 (99 regular, 2 scan edges) • Antenna connector type : SO-239 × 2 and phono jack (RCA; 50 ø impedance) • Temperature range : 0˚C to +50˚C (+32˚F to +122˚F) • Frequency stability : Less than ±0.5 ppm 5 min. after power ON. (0˚C to +50˚C; +32˚F to +122˚F) • Frequency resolution : 1 Hz • Power supply : 13.8 V DC ±15% (negative ground) • Power consumption Transmit : Max. power 23 A Receive : Standby 3.0 A Max. audio 3.5 A • Dimensions : 340(W) × 116(H) × 279.3(D) mm (projections not included) 133⁄8(W) × 49⁄16(H) × 11(D) in • Weight (approx.) : 10.0 kg; 22 lb • ACC 1 connector : 8-pin DIN connector • ACC 2 connector : 7-pin DIN connector • CI-V connector : 2-conductor 3.5 (d) mm (1⁄8″) • Display : 5.8-inch (diagonal) TFT color LCD ■ Transmitter • Output power (continuously adjustable) SSB/CW/RTTY/FM : Less than 2 to 100 W AM : Less than 1 to 30 W • Modulation system SSB : Digital PSN modulation AM : Digital Low power modulation FM : Digital Phase modulation • Spurious emission HF bands : Less than -50 dB 50 MHz band : Less than -63 dB • Carrier suppression : More than 40 dB • Unwanted sideband : More than 55 dB suppression • ∂TX variable range : ±9.999 kHz • Microphone connector : 8-pin connector (600 ø) • ELEC-KEY connector : 3-conductor 6.35(d) mm (1⁄4″) • KEY connector : 3-conductor 6.35(d) mm (1⁄4″) • SEND connector : Phono jack (RCA) • ALC connector : Phono jack (RCA) ■ Receiver • Receive system : Double superheterodyne system • Intermediate frequencies 1st : 64.455 MHz 2nd : 36 kHz • Sensitivity (typical) SSB, CW, RTTY : 0.15 µV (1.80-29.99 MHz)*1 (10 dB S/N) BW=2.4 kHz 0.12 µV (50.0-54.0 MHz)*2 AM (10 dB S/N) : 6.3 µV (0.1-1.799 MHz)*1 BW=6 kHz 2 µV (1.80-29.99 MHz)*1 1.6 µV (50.0-54.0 MHz)*2 FM (12 dB SINAD) : 0.5 µV (28.0-29.99 MHz)*1 BW=15 kHz 0.3 µV (50.0-54.0 MHz)*2 *1Pre-amp 1 is ON. *2Pre-amp 2 is ON. • Squelch sensitivity (Pre-amp: ON) SSB : Less than 3.2 µV FM : Less than 0.3 µV • Selectivity (IF filter shape is set to SHARP.) SSB (BW: 2.4 kHz) : More than 2.4 kHz/-6 dB Less than 3.8 kHz/-60 dB CW (BW: 500 Hz) : More than 500 Hz/-6 dB Less than 900 Hz/-60 dB RTTY (BW: 350 Hz) : More than 350 Hz/-6 dB Less than 650 Hz/-60 dB AM (BW: 6 kHz) : More than 6.0 kHz/-6 dB Less than 15.0 kHz/-60 dB FM (BW: 15 kHz) : More than 12.0 kHz/-6 dB Less than 20.0 kHz/-60 dB • Spurious and image : More than 70 dB rejection ratio (except IF through on 50 MHz band) • AF output power : More than 2.0 W at 10% (at 13.8 V DC) distortion with an 8 ø load • RIT variable range : ±9.999 kHz • PHONES connector : 3-conductor 6.35 (d) mm (1⁄4″) • External SP connector : 2-conductor 3.5 (d) mm (1⁄8″)/8 ø • DSP ANF attenuation : More than 30 dB (with 1 kHz single tone) • DSP NR attenuation : More than 6 dB (noise rejection in SSB) ■ Antenna tuner • Matching impedance range HF bands : 16.7 to 150 ø unbalanced (Less than VSWR 3:1) 50 MHz band : 20 to 125 ø unbalanced (Less than VSWR 2.5:1) • Minimum operating input : 8 W (HF bands) power 15 W (50MHz band) • Tuning accuracy : VSWR 1.5:1 or less • Insertion loss : Less than 1.0 dB (after tuning at RF power 100W) Spurious signals may be displayed on the spectrum scope screen regardless of the transceiver's state (Tx or Rx). They are generated in the scope circuit. This does not indicate a transceiver malfunction. All stated specifications are typical and subject to change without notice or obligation. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 160