Icom IC-7600 Instruction Manual - Page 28

■ Linear amplifier connections, ◇ Connecting the IC-PW1/EURO

Page 28 highlights

2 INSTALLATION AND CONNECTIONS ■ Linear amplifier connections D Connecting the IC-PW1/EURO To an antenna ACC-1 Remote control cable (supplied with the IC-PW1/EURO) ACC cable (supplied with the IC-PW1/EURO) Coaxial cable REMOTE (supplied with the ANT IC-PW1/EURO) Be sure to connect the cable to the 7-pin ACC 2 jack. INPUT1 &9$*5&3   INPUT2 Coaxial cable* Connect [INPUT2] if necessary GND ANT1 ANT2 ACC 2 REMOTE GND IC-PW1/EURO AC outlet GND (Non-European versions : 100-120/220-240 V European version : 230 V) Transceiver *Purchase separately D Connecting a non-Icom linear amplifier Transceiver ANT1 To an antenna ALC 50 ø coaxial cable RF OUTPUT RF INPUT ALC SEND Non-Icom linear amplifier SEND R WARNING: Set the transceiver output power and linear amplifier ALC output level after referring to the linear amplifier instruction manual. The ALC input level must be in the range 0 V to - 4 V. The transceiver does not accept positive voltage. Non-matched ALC and RF power settings could overheat or damage the linear amplifier. The maximum signal level of [SEND] jack is 16 V/0.5 A DC with initial setting, and 250 V/ 200 mA with "MOSFET" setting (see p. 125 for details). Use an external relay unit if your non-Icom linear amplifier requires control voltage and/or current greater than specified. 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180

Linear amplifier connections
D
Connecting the IC-PW1/EURO
EXCITER
1
1&2
To an
antenna
ACC-1
ANT
ANT2
ANT1
ACC 2
INPUT1
INPUT2
REMOTE
GND
IC-PW1/EURO
AC outlet
(Non-European versions : 100–120/220–240 V
European version
: 230 V)
Transceiver
REMOTE
Remote control cable
(supplied with the IC-PW1/EURO)
ACC cable
(supplied with the IC-PW1/EURO)
Be sure to connect the cable
to the 7-pin ACC 2 jack.
Coaxial cable
(supplied with the
IC-PW1/EURO)
Coaxial cable*
*Purchase separately
Connect
[INPUT2]
if necessary
GND
GND
D
Connecting a non-Icom linear amplifier
RF OUTPUT
RF INPUT
ALC
SEND
50
ø
coaxial
cable
Transceiver
ANT1
ALC
SEND
To an
antenna
Non-Icom linear amplifier
R
WARNING:
Set the transce±ver output power and l±near
ampl±f±er ALC output level after referr±ng to the
l±near ampl±fier ±nstruct±on manual.
The ALC ±nput level must be ±n the range 0 V to –
4 V. The transce±ver does not accept pos±t±ve volt-
age. Non-matched ALC and RF power sett±ngs
could overheat or damage the l±near ampl±fier.
The max±mum s±gnal level of [SEND] jack ±s
16 V/0.5 A DC w±th ±n±t±al sett±ng, and 250 V/
200 mA w±th “MOSFET” sett±ng (see p. 125 for de-
ta±ls). Use an external relay un±t ±f your non-Icom
l±near ampl±f±er requ±res control voltage and/or
current greater than spec±fied.
21
2
INSTALLATION AND CONNECTIONS