Icom IC-7600 Instruction Manual - Page 173
CE, CE
View all Icom IC-7600 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 173 highlights
CE 15 INSTALLATION NOTES For amateur base station installations it is recommended that the forward clearance in front of the antenna array is calculated relative to the EIRP (Effective Isotropic Radiated Power). The clearance height below the antenna array can be determined in most cases from the RF power at the antenna input terminals. As different exposure limits have been recommended for different frequencies, a relative table shows a guideline for installation considerations. Below 30 MHz, the recommended limits are specified in terms of V/m or A/m fields as they are likely to fall within the near-field region. Similarly, the antennas may be physically short in terms of electrical length and that the installation will require some antenna matching device which can create local, high intensity magnetic fields. Analysis of such MF installations is best considered in association with published guidance notes such as the FCC OET Bulletin 65 Edition 97-01 and its annexes relative to amateur transmitter installations. The EC recommended limits are almost identical to the FCC specified 'uncontrolled' limits and tables exist that show pre-calculated safe distances for different antenna types for different frequency bands. Further information can be found at http://www.arrl.org/. • Typical amateur radio installation Exposure distance assumes that the predominant radiation pattern is forward and that radiation vertically downwards is at unity gain (sidelobe suppression is equal to main lobe gain). This is true of almost every gain antenna today. Exposed persons are assumed to be beneath the antenna array and have a typical height of 1.8 m. The figures assume the worst case emission of a constant carrier. For the bands 10 MHz and higher the following power density limits have been recommended: 10-50 MHz 2 W/sq m Vertical clearance by EIRP output 1 Watts 2.1 m 10 Watts 2.8 m 25 Watts 3.4 m 100 Watts 5 m 1000 Watts 12 m Forward clearance by EIRP output 100 Watts 2 m 1000 Watts 6.5 m 10,000 Watts 20 m 100,000 Watts 65 m In all cases any possible risk depends on the transmitter being activated for long periods. (actual recommendation limits are specified as an average during 6 minutes) Normally the transmitter is not active for long periods of time. Some radio licenses will require that a timer circuit automatically cuts off the transmitter after 1-2 minutes etc. Similarly some modes of transmission, SSB, CW, AM etc. have a lower 'average' output power and the assessed risk is even lower. Versions of the IC-7600 which display the "CE" symbol on the serial number seal, comply with the essential requirements of the European Radio and Telecommunication Terminal Directive 1999/5/EC. This warning symbol indicates that this equipment operates in non-harmonised frequency bands and/or may be subject to licensing conditions in the country of use. Be sure to check that you have the correct version of this radio or the correct programming of this radio, to comply with national licensing requirement. • List of Country codes (ISO 3166-1) Country 1 Austria 2 Belgium 3 Bulgaria 4 Croatia 5 Czech Republic 6 Cyprus 7 Denmark 8 Estonia 9 Finland 10 France 11 Germany 12 Greece 13 Hungary 14 Iceland 15 Ireland 16 Italy 17 Latvia Codes AT BE BG HR CZ CY DK EE FI FR DE GR HU IS IE IT LV Country 18 Liechtenstein 19 Lithuania 20 Luxembourg 21 Malta 22 Netherlands 23 Norway 24 Poland 25 Portugal 26 Romania 27 Slovakia 28 Slovenia 29 Spain 30 Sweden 31 Switzerland 32 Turkey 33 United Kingdom Codes LI LT LU MT NL NO PL PT RO SK SI ES SE CH TR GB 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 166