Kyocera KM-C2030 KM-C3130/C2030 Operation Guide Basic Oper Rev-1B - Page 92

Specifying Copy Settings

Get Kyocera KM-C2030 PDF manuals and user guides View all Kyocera KM-C2030 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

5.2 Selecting a Finishing Setting 5 Specifying Copy Settings Chapter 5 ❍ For details on the "User's Choice" functions, refer to "Specifying Default Settings ("User's Choice" Functions)" in the Administrator Operations volume. Stapling (with finisher DF-620 installed) The copies are bound together with a staple in the corner. However, stapling is only performed if the following conditions are met. G The number of copies is set to between 2 and 30. G If standard-size paper is used, the paper sizes must be Letter L, Letter C, Exec- utive L (7-1/4 × 10-1/2 in. L), Executive C (7-1/4 × 10-1/2 in. C), Legal L and 11 × 17 L. G If nonstandard-size paper is used, the paper width must be between 7-1/4 in. and 11-3/4 in. G If nonstandard-size paper is used, the paper length must be between 7-1/4 in. and 17 in. G The copier must not enter Interrupt mode. Stapling (with finisher DF-625 installed) The copies are bound together with a staple. Either the "Corner Staple" or the "2Point Staple" Finishing setting can be selected. However, stapling is only performed if the following conditions are met. G The number of copies is set to between 2 and 50. (However, if the paper length is 11-3/4 in. or more, the number of copies can only be set to 25 or less.) G If standard-size paper is used, the paper sizes must be Letter L, Letter C, Legal L and 11 × 17 L. G If nonstandard-size paper is used, the paper width must be between 7-1/4 in. and 11-3/4 in. G If nonstandard-size paper is used, the paper length must be between 7-1/4 in. and 17 in. G The copier must not enter Interrupt mode. Hole-Punching Two holes for filing copies in binders can be punched. The position of the punched holes can be specified along the left side or along the top. However, hole-punching is only performed if the following conditions are met. G Finisher DF-625 is installed. G Punch kit PH-620 is installed. G If standard-size paper is used, the paper sizes must be as follows: Letter L, Letter C, Legal L and 11 × 17 L (with the "2-Hole Punch" setting) Letter C and 11 × 17 L (with the "3-Hole Punch" setting). G If nonstandard-size paper is used, the paper width must be between 7-1/4 in. and 11-3/4 in. 5-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
5.2 Selecting a Finishing Setting
5
5-5
Specifying Copy Settings
Chapter 5
❍
For details on the
“
User
’
s Choice
”
functions, refer to
“
Specifying Default Set-
tings (
“
User
’
s Choice
”
Functions)
”
in the Administrator Operations volume.
Stapling (with finisher DF-620 installed)
The copies are bound together with a staple in the corner.
However, stapling is only performed if the following conditions are met.
±
The number of copies is set to between 2 and 30.
±
If standard-size paper is used, the paper sizes must be Letter L, Letter C, Exec-
utive L (7-1/4
×
10-1/2 in. L), Executive C (7-1/4
×
10-1/2 in. C), Legal L and
11
×
17 L.
±
If nonstandard-size paper is used, the paper width must be between 7-1/4 in.
and 11-3/4 in.
±
If nonstandard-size paper is used, the paper length must be between 7-1/4 in.
and 17 in.
±
The copier must not enter Interrupt mode.
Stapling (with finisher DF-625 installed)
The copies are bound together with a staple. Either the
“
Corner Staple
”
or the
“
2-
Point Staple
”
Finishing setting can be selected.
However, stapling is only performed if the following conditions are met.
±
The number of copies is set to between 2 and 50. (However, if the paper length
is 11-3/4 in. or more, the number of copies can only be set to 25 or less.)
±
If standard-size paper is used, the paper sizes must be Letter L, Letter C,
Legal L and 11
×
17 L.
±
If nonstandard-size paper is used, the paper width must be between 7-1/4 in.
and 11-3/4 in.
±
If nonstandard-size paper is used, the paper length must be between 7-1/4 in.
and 17 in.
±
The copier must not enter Interrupt mode.
Hole-Punching
Two holes for filing copies in binders can be punched. The position of the punched
holes can be specified along the left side or along the top.
However, hole-punching is only performed if the following conditions are met.
±
Finisher DF-625 is installed.
±
Punch kit PH-620 is installed.
±
If standard-size paper is used, the paper sizes must be as follows:
Letter L, Letter C, Legal L and 11
×
17 L (with the
“
2-Hole Punch
”
setting)
Letter C and 11
×
17 L (with the
“
3-Hole Punch
”
setting).
±
If nonstandard-size paper is used, the paper width must be between 7-1/4 in.
and 11-3/4 in.