Olympus E-300 EVOLT E-300 Advanced Manual (English) - Page 180

Set PC MODE to AUTO or STORAGE. When

Get Olympus E-300 - EVOLT Digital Camera SLR PDF manuals and user guides
UPC - 050332298859
View all Olympus E-300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 180 highlights

If you encounter problems Possible cause Corrective action The top left part of the picture appears too bright. Ref. Page When shooting at slow shutter speeds, noise may be generated due to a rise in temperature in the CCD drive circuit. Set NOISE REDUCTION to ON before taking pictures. P. 105 Pictures cannot be played back on the monitor. Pictures are not stored on NO PICTURE appears on the monitor. Record - the card. pictures. The card error occurs. Refer to "Error codes". No picture is displayed on the TV when connected to the camera. P. 174 The video cable is not connected correctly. Connect the cable properly according to the instructions. P. 116 The camera's video output signal is incorrect. Set the video signal according to the region where used. P. 134 The TV 's video signal is Set the TV to the video input mode. - incorrect. The monitor is hard to see. The brightness is not adjusted properly. Adjust the brightness of the monitor using the menu. P. 131 The monitor is exposed to Block the sunlight with your hand. - direct sunlight. The computer does not recognize the camera correctly. The camera's power is Set the power switch to ON. - 11 turned off. Appendix The USB driver was not successfully installed. Install the OLYMPUS Master. P. 158 The camera's PC MODE is set to CONTROL. Set PC MODE to AUTO or STORAGE. When AUTO is set, the selection screen for USB connection is displayed every time you connect the USB cable to the camera. P. 132 180

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
11
Appendix
The camera's power is
turned off.
The USB driver was not
successfully installed.
The camera's PC MODE
is set to CONTROL.
Set the power switch to
ON
.
Install the OLYMPUS Master.
Set PC MODE to AUTO or STORAGE. When
AUTO is set, the selection screen for USB
connection is displayed every time you connect
the USB cable to the camera.
–
P. 158
P. 132
180
If you encounter problems
Possible cause
Corrective action
Ref. Page
The top left part of the picture appears too bright.
When shooting at slow
shutter speeds, noise may
be generated due to a rise
in temperature in the CCD
drive circuit.
Set NOISE REDUCTION to ON before taking
pictures.
P. 105
Pictures are not stored on
the card.
The card error occurs.
NO PICTURE appears on the monitor. Record
pictures.
Refer to “Error codes”.
–
P. 174
The video cable is not
connected correctly.
The camera's video
output signal is incorrect.
The TV 's video signal is
incorrect.
Connect the cable properly according to the
instructions.
Set the video signal according to the region
where used.
Set the TV to the video input mode.
P. 116
P. 134
–
Adjust the brightness of the monitor using the
menu.
Block the sunlight with your hand.
P. 131
–
The brightness is not
adjusted properly.
The monitor is exposed to
direct sunlight.
The computer does not recognize the camera correctly.
No picture is displayed on the TV when connected to the camera.
Pictures cannot be played back on the monitor.
The monitor is hard to see.