TP-Link TD-W8950ND User Guide - Page 51

URL Filtering

Get TP-Link TD-W8950ND PDF manuals and user guides
UPC - 845973060404
View all TP-Link TD-W8950ND manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

TD-W8950ND 150Mbps Wireless Lite N ADSL2+ Modem Router User Guide Figure 4-46 2. Enter the Filter name for the rule, it is exclusive and must be filled in. 3. Select Protocol in the drop-down list, enter Source IP address, Source Subnet Mask, Source Port, Destination IP address, Destination Subnet Mask, and Destination Port for the rule. 4. Select at least one WAN interfaces displayed below to apply this rule. 5. Click Save/Apply to save this entry. ) Note: When you add an Incoming IP Filtering entry, you must configure at least one condition on the preceding screen except the Filter name. If you leave Protocol blank, it means that the rule is effective to all protocols, if you leave the Source IP address and/or Destination IP address blank, it suggests that all Source IP addresses and/or Destination IP addresses are controlled by the rule, if you leave the Source Port and/or Destination Port blank, it suggests that all Source Ports and/or Destination Ports are controlled by the rule. 4.5.5.3 URL Filtering This section allows you to configure the filter rules based on URL to control the computers in the LAN to access the specified port. Figure 4-47 44

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
TD-W8950ND
150Mbps Wireless Lite N ADSL2+ Modem Router User Guide
Figure 4-46
2.
Enter the Filter name for the rule, it is exclusive and must be filled in.
3.
Select Protocol in the drop-down list, enter Source IP address, Source Subnet Mask, Source
Port, Destination IP address, Destination Subnet Mask, and Destination Port for the rule.
4.
Select at least one WAN interfaces displayed below to apply this rule.
5.
Click Save/Apply to save this entry.
)
Note:
When you add an Incoming IP Filtering entry, you must configure at least one condition on the
preceding screen except the Filter name. If you leave Protocol blank, it means that the rule is
effective to all protocols, if you leave the Source IP address and/or Destination IP address blank, it
suggests that all Source IP addresses and/or Destination IP addresses are controlled by the rule,
if you leave the Source Port and/or Destination Port blank, it suggests that all Source Ports and/or
Destination Ports are controlled by the rule.
4.5.5.3 URL Filtering
This section allows you to configure the filter rules based on URL to control the computers in the
LAN to access the specified port.
Figure 4-47
44