TP-Link TD-W8950ND User Guide - Page 57

Default Gateway, 4.5.7.2 Static Route

Get TP-Link TD-W8950ND PDF manuals and user guides
UPC - 845973060404
View all TP-Link TD-W8950ND manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

TD-W8950ND 150Mbps Wireless Lite N ADSL2+ Modem Router User Guide 4.5.7.1 Default Gateway Choose "Routing→Default Gateway" menu, you can configure the Default Gateway routing in the next screen as shown in Figure 4-59. Figure 4-59 ¾ Enable Automatic Assigned Default Gateway - Select this checkbox, and then the Router will accept the first received default gateway assignment from one of the PPPoA, PPPoE or MER/DHCP enabled PVC(s). If this checkbox is not selected, you have to enter the static default gateway and/or an interface. Click Save/Apply to save your configurations. ) Note: If changing the Enable Automatic Assigned Default Gateway from unselected to selected, you must reboot the Router to get the automatic assigned default gateway. 4.5.7.2 Static Route Choose "Routing→Static Route" menu, you can view and add the Static Route entry in the next screen as shown in Figure 4-60. A static route is a pre-determined path that network information must travel to reach a specific host or network. Figure 4-60 To add a new entry, follow the steps below. 1. Click the Add button in Figure 4-60 to go to the Static Route Add page as shown in Figure 4-61. 2. Enter the IP address of the destination network. This parameter specifies the IP network address of the final destination. 3. Enter the Subnet Mask for the destination. 4. Select the Use Gateway IP Address checkbox and enter the IP address of the gateway. The gateway is an immediate neighbor of your ADSL Router that will forward the packet to the destination. On the LAN, the gateway must be a router on the same segment as your Router; over Internet (WAN), the gateway must be the IP address of one of the remote nodes. 50

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
TD-W8950ND
150Mbps Wireless Lite N ADSL2+ Modem Router User Guide
4.5.7.1 Default Gateway
Choose “Routing
→
Default Gateway” menu, you can configure the Default Gateway routing in the
next screen as shown in Figure 4-59.
Figure 4-59
¾
Enable Automatic Assigned Default Gateway - Select this checkbox, and then the Router will
accept the first received default gateway assignment from one of the PPPoA, PPPoE or
MER/DHCP enabled PVC(s). If this checkbox is not selected, you have to enter the static
default gateway and/or an interface. Click Save/Apply to save your configurations.
)
Note:
If changing the Enable Automatic Assigned Default Gateway from unselected to selected, you
must reboot the Router to get the automatic assigned default gateway.
4.5.7.2 Static Rout
e
Choose “Routing
→
Static Route” menu, you can view and add the Static Route entry in the next
screen as shown in Figure 4-60. A static route is a pre-determined path that network information
must travel to reach a specific host or network.
Figure 4-60
To add a new entry, follow the steps below.
1.
Click the Add button in Figure 4-60 to go to the Static Route Add page as shown in Figure
4-61.
2.
Enter the IP address of the destination network. This parameter specifies the IP network
address of the final destination.
3.
Enter the Subnet Mask for the destination.
4.
Select the Use Gateway IP Address checkbox and enter the IP address of the gateway. The
gateway is an immediate neighbor of your ADSL Router that will forward the packet to the
destination. On the LAN, the gateway must be a router on the same segment as your Router;
over Internet (WAN), the gateway must be the IP address of one of the remote nodes.
50