Yamaha 01V Owner's Manual - Page 268
Analog Inputs, Analog Outputs
View all Yamaha 01V manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 268 highlights
268 Appendix B: Specifications Analog Inputs Actual For Use Connection PAD GAIN Load With Impedance Nominal Input level Sensitivity*1 Nominal Max. Before Clip Connector in Console 0 -60 Input channels 1-12 0 -16 26 -20 Input channels 13-16 +10 2TR IN (L, R) 3 kΩ 10 kΩ 10 kΩ 50-600 Ω Mics & 600 Ω Lines 600 Ω Lines 600 Ω Lines -66 dB (388 µV) -22 dB (61.6 mV) +4 dB (1.23 V) -26 dB (38.8 mV) +4 dB (1.23 V) -10 dBV (316 mV) -60 dB (775 µV) -16 dB (123 mV) +10 dB (2.45 V) -20 dB (77.5 mV) +10 dB (2.45 V) -10 dBV (316 mV) -46 dB (3.88 mV) -2 dB (616 mV) +24 dB (12.3 V) -6 dB (388 mV) +24 dB (12.3 V) +4 dBV (1.58 V) XLR-3-31 type (balanced)*2 & TRS phone jack (balanced)*3 TRS phone jack (balanced)3 Phono (unbalanced) *1. Sensitivity is the lowest level that will produce an output of +4 dB (1.23 V) or the nominal output level when the 01V is set to maximum gain (all faders and level controls at maximum positions). *2. Input channel XLR-type connectors are balanced (pin 1 = ground, pin 2 = hot, pin 3 = cold). *3. Input channel phone jacks are balanced (tip = hot, ring = cold, sleeve = ground). * Where dB represents a specific voltage, 0 dB is referenced to 0.775 V rms. * For 2TR IN levels, 0 dBV is referenced to 1.00 V rms. * Input channels 1-16 and ST IN use linear 20-bit 128-times oversampling A/D converters. * +48 V DC phantom powering switched in 6-channel blocks (1-6, 7-12) available via the XLR-type connectors of input channels 1-12 Analog Outputs Connection Actual Source Impedance For Use With Nominal Output Level Nominal Max. Before Clip Connector in Console STEREO OUT (L, R) OMNI OUT (1-4) 2TR OUT (L, R) MONITOR OUT (L, R) PHONES 150 Ω 150 Ω 600 Ω 150 Ω 100 Ω 600 Ω Lines 10 kΩ Lines 10 kΩ Lines 10 kΩ Lines 8 Ω phones 40 Ω phones +4 dB (1.23 V) +4 dB (1.23 V) -10 dBV (316 mV) +4 dB (1.23 V) 4 mW 12 mW +18 dB (6.16 V) +18 dB (6.16 V) +4 dBV (1.58 V) +18 dB (6.16 V) 25 mW 75 mW XLR-3-32 type (balanced)*1 TRS phone jack (balanced)*2 Phono (unbalanced) TRS phone jack (balanced)2 Stereo phone jack (unbalanced)*3 *1. STEREO OUT XLR-type connectors are balanced (pin 1 = ground, pin 2 = hot, pin 3 = cold). *2. OMNI/MONITOR OUT TRS phone jacks are balanced (tip = hot, ring = cold, sleeve = ground). *3. PHONES stereo phone jack is unbalanced (tip = send, ring = return, sleeve = ground). * For 2TR OUT, 0 dBV is referenced to 1.00 V rms. * Where dB represents a specific voltage, 0 dB is referenced to 0.775 V rms. * STEREO OUT uses 20-bit 8-times oversampling D/A converters. * OMNI OUT 1-4 and MONITOR OUT use 18-bit 8-times oversampling D/A converters. 01V-Owner's Manual