Yamaha 01V Owner's Manual - Page 281
PARAMETER CHANGE byte operation for type, 0x01:system memory
View all Yamaha 01V manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 281 highlights
282 MIDI Data Format PARAMETER CHANGE (7bit operation for type 0x10:edit buffer) Reception This message is received if [Parameter Change RX] is ON and the [Rx CH] matches the Device Channel included in the SUB STATUS. This is echoed if [Parameter Change ECHO] is ON. When this is received, the specified parameter will be controlled. Transmission If [Parameter Change TX] is ON, this message is transmitted on the [Tx CH] Device Channel when a parameter not specified in the [Control Assign Table] is modified. STATUS ID No. SUB STATUS GROUOP ID MODEL ID PARAM TYPE DATA EOX 11110000 F0 01000011 43 0001nnnn 1n 00111110 3e 00000100 04 00010000 10 0aaaaaaa dd0 0aaaaaaa dd1 0ddddddd dd2 : 11110111 F7 System Exclusive Message Manufacturer's ID No.(YAMAHA) parameter change n=0-15(Device Channel No.1-16) MODEL ID Device code (01V) 7bit operation for edit buffer (type) address( H) high 7 bits of 14 bits address address( L) low 7 bits of 14 bits address data 7bit : End Of Exclusive The valid range of addresses is 0x0000 - 0x03FF PARAMETER CHANGE (bit operation for type 0x40:edit buffer) Reception When [Parameter Change RX] is ON, this message is received if the [Rx CH] matches the Device Channel included in the SUB STATUS. If [Parameter Change ECHO] is ON, this message will be echoed. When this message is received, the specified parameter will be controlled. Transmission If [Parameter Change TX] is ON, this message is transmitted on the [Tx CH] Device Channel when a parameter not specified in the [Control Assign Table] is modified. STATUS ID No. SUB STATUS GROUOP ID MODEL ID PARAM TYPE DATA EOX 11110000 F0 01000011 43 0001nnnn 1n 00111110 3e 00000100 04 01000000 40 0aaaaaaa dd0 0aaaaaaa dd1 0ddddddd dd2 : 11110111 F7 System Exclusive Message Manufacturer's ID No.(YAMAHA) parameter change n=0-15(Device Channel No.1-16) MODEL ID Device code (01V) bit operation for edit buffer (type) address( H) high 7 bits of 14 bits address address( L) low 7 bits of 14 bits address data(bit0-2:change bit no.0-7, bit3:0=reset 1=set) : End Of Exclusive The valid range of addresses is 0x0000 - 0x03FF PARAMETER CHANGE (byte operation for type 0x01:system memory) Reception When [Parameter Change RX] is ON, this message is received if the [Rx CH] matches the Device Channel included in the SUB STATUS. When [Parameter Change ECHO] is ON, this is echoed. When this is received, the specified parameter will be controlled. STATUS ID No. SUB STATUS GROUOP ID MODEL ID PARAM TYPE DATA EOX 11110000 F0 01000011 43 0001nnnn 1n 00111110 3e 00000100 04 00000001 01 0aaaaaaa dd0 0aaaaaaa dd1 0000dddd dd2 0000dddd dd3 : 11110111 F7 System Exclusive Message Manufacturer's ID No.(YAMAHA) parameter change or response n=0-15(Device Channel No.1-16) MODEL ID Device code (01V) byte operation for system memory (type) address( H) high 7 bits of 14 bits address address( L) low 7 bits of 14 bits address data( H) high 4 bits of 8 bits data data( L) low 4 bits of 8 bits data : continuous address datas End Of Exclusive The system memory will depend on the address, as follows. 0x0000 - 0x007F : setup memory(128byte) 0x0080 - 0x0147 : backup memory(200byte) 0x0200 : card type(1byte) PARAMETER CHANGE (bit operation for type 0x41:system memory) Reception When [Parameter Change RX] is ON, this message is received if the [Rx CH] matches the Device Channel included in the SUB STATUS. When [Parameter Change ECHO] is ON, this is echoed. When this is received, the specified parameter will be controlled. STATUS ID No. SUB STATUS GROUOP ID MODEL ID PARAM TYPE DATA EOX 11110000 F0 01000011 43 0001nnnn 1n 00111110 3e 00000100 04 01000001 41 0aaaaaaa dd0 0aaaaaaa dd1 0ddddddd dd2 : 11110111 F7 System Exclusive Message Manufacturer's ID No.(YAMAHA) parameter change or response n=0-15(Device Channel No.1-16) MODEL ID Device code (01V) bit operation for system memory (type) address( H) high 7 bits of 14 bits address address( L) low 7 bits of 14 bits address data(bit0-2:change bit no.0-7, bit3:0=reset 1=set) : End Of Exclusive The system memory will depend on the address, as follows. 0x0000 - 0x007F : setup memory(128byte) 0x0080 - 0x0147 : backup memory(200byte) 01V-Owner's Manual