Yamaha 01V Owner's Manual - Page 280
Transmission Condition, Receive Condition, Parameter Change, 3 Active Sensing Fe, Basic Format
View all Yamaha 01V manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 280 highlights
MIDI Data Format 281 1.3 ACTIVE SENSING (Fe) Reception Once this message has been received, an interval of 300ms or more during which no message is received will cause MIDI communications to be initialized, clearing Running Status etc. STATUS 11111110 FE Active Sensing 2. TRANSMISSION CONDITION CONTROL CHANGE $BnH PROGRAM CHANGE $CnH SYSTEM EXCLUSIVE PARAMETER CHANGE $F0H, $43H, $1nH (RESPONSE FOR PARAMETER REQUEST) CTL Tx ON PGM Tx ON PARAM Tx ON SYSTEM EXCLUSIVE BULK DUMP $F0H, $43H, $0nH BULK REQUEST $F0H, $43H, $2nH USER DEFINE MMC $F0H, $7FH, nnH, 06H MIDI TX CH? MIDI OUT MIDI IN CTL ECHO ON PGM ECHO ON PARAM ECHO ON 3. RECEIVE CONDITION MIDI IN MIDI Rx CH? PGM OMNI ON CTL OMNI ON PARAM OMNI ON CTL Rx ON PGM Rx ON PARAM Rx ON BULK Rx ON $8nH NOTE OFF $9nH NOTE ON/OFF $BnH CONTROL CHANGE $CnH PROGRAM CHANGE SYSTEM EXCLUSIVE $F0H, $43H, $1nH PARAMETER CHANGE $F0H, $43H, $3nH PARAMETER REQUEST SYSTEM EXCLUSIVE $F0H, $43H, $0nH, BULK DUMP $F0H, $43H, $2nH, BULK REQUEST CTL ECHO ON PGM ECHO ON PARAM ECHO ON MIDI OUT 4. PARAMETER CHANGE BASIC FORMAT STATUS ID No. SUB STATUS GROUP ID MODEL ID PARAM TYPE DATA EOX 11110000 F0 01000011 43 0pppnnnn pn 00111110 3e 00000100 04 0ttttttt tt 0ddddddd dd0 : 0ddddddd ddn 11110111 F7 System Exclusive Message Manufacturer's ID No.(YAMAHA) p=mode 1:parameter change or response for request, 3:parameter request n=0-15(Device Channel No.1-16) MODEL ID (digital mixer) Device code (01V) (type) data 0 : data n End Of Exclusive type 0x00 edit buffer ...byte operation format 0x01 system memory (setup, backup) ...byte operation format 0x02 function call (mem/lib recall, mem/lib store, clear, title) 0x03 controller (LCD/fader mode)...byte operation format 0x04 multiple link (fader mode, solo mode, title,,,) 0x05 remote meter (meter data) 0x10 edit buffer ...7bit operation format 0x40 edit buffer ...bit operation format 0x41 system memory (setup, backup) ...bit operation format 0x43 controller (key remote) ...bit operation format PARAMETER CHANGE (byte operation for type 0x00:edit buffer) Reception This message is received if [Parameter Change RX] is ON and the [Rx CH] matches the Device Channel included in the SUB STATUS. If [Parameter Change ECHO] is ON, this will be echoed. The specified parameter will be controlled when this message is received. Transmission If [Parameter Change TX] is ON, this message will be transmitted on the [Tx CH] Device Channel when a parameter that is not specified in the [Control Assign Table] is modified. STATUS ID No. SUB STATUS GROUOP ID MODEL ID PARAM TYPE DATA EOX 11110000 F0 01000011 43 0001nnnn 1n 00111110 3e 00000100 04 00000000 00 0aaaaaaa dd1 0aaaaaaa dd2 0000dddd dd3 0000dddd dd4 : : 11110111 F7 System Exclusive Message Manufacturer's ID No.(YAMAHA) parameter change or response n=0-15(Device Channel No.1-16) MODEL ID Device code (01V) byte operation for edit buffer (type) address( H) high 7 bits of 14 bits address address( L) low 7 bits of 14 bits address data( H) high 4 bits of 8 bits data data( L) low 4 bits of 8 bits data : continuous address datas End Of Exclusive The valid range of addresses is 0x0000 - 0x03FF 01V-Owner's Manual