3Com 3C13886 Installation Guide - Page 33

Low-End and Mid-Range Series Routers Cable, Manual, Caution

Get 3Com 3C13886 - Router OC-3 ATM SML Flexible Interface Card PDF manuals and user guides
UPC - 662705478456
View all 3Com 3C13886 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

3Com Router Module Guide Chapter 2 Smart Interface Cards Note: A network interface connector is available for extending the E1 cable. Both ends of the connector are RJ-45 jacks that can be used to connect two 120-ohm balanced twisted pair cables. In addition, a 75-ohm to 120-ohm adapter is available. For the pinouts of E1 cables, see Low-End and Mid-Range Series Routers Cable Manual. Caution: E1 cable, coaxial connector, network interface connector and 75ohm-to-120ohm adapter are optional, which must be ordered together with ROUTER 1-PORT FRACTIONAL E1 SIC. Otherwise they will not be supplied. 2.4.7 Connecting Interface Cable Caution: When using E1 cable outdoors, you are recommended to install a special lightning arrester on the input end of the cable in order to avoid lightning more effectively. If the SIC has been properly installed, follow these steps to connect the cable: Step 1: Check the type of E1 cable and correctly set the DIP switch (the ex-factory setting of E1/cE1/PRI interface impedance is 75-ohm); Step 2: Connect the DB15 connector of E1 cable to ROUTER 1-PORT FRACTIONAL E1 SIC; Step 3: Connect the other end of the E1 cable to the corresponding network device: 1) When the E1 cable is a 75-ohm unbalanced coaxial cable: z Directly connect the BNC connector of the cable to the remote equipment if there is no need for extension, or z Connect the BNC connector of the cable to the coaxial connector and the other end of the coaxial connector to the remote network equipment through a 75-ohm E1 trunk cable, if cable extension is needed. 2-18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
3Com Router Module Guide
Chapter 2
Smart Interface Cards
2-18
Note:
A network interface connector is available for extending the E1 cable. Both ends of the connector are
RJ-45 jacks that can be used to connect two 120-ohm balanced twisted pair cables.
In addition, a 75-ohm to 120-ohm adapter is available.
For the pinouts of E1 cables, see
Low-End and Mid-Range Series Routers Cable
Manual
.
Caution:
E1 cable, coaxial connector, network interface connector and 75ohm-to-120ohm adapter are optional,
which must be ordered together with ROUTER 1-PORT FRACTIONAL E1 SIC. Otherwise they will not
be supplied.
2.4.7
Connecting Interface Cable
Caution:
When using E1 cable outdoors, you are recommended to install a special lightning arrester on the input
end of the cable in order to avoid lightning more effectively.
If the SIC has been properly installed, follow these steps to connect the cable:
Step 1: Check the type of E1 cable and correctly set the DIP switch (the ex-factory
setting of E1/cE1/PRI interface impedance is 75-ohm);
Step 2: Connect the DB15 connector of E1 cable to ROUTER 1-PORT FRACTIONAL
E1 SIC;
Step 3: Connect the other end of the E1 cable to the corresponding network device:
1)
When the E1 cable is a 75-ohm unbalanced coaxial cable:
Directly connect the BNC connector of the cable to the remote equipment if there
is no need for extension, or
Connect the BNC connector of the cable to the coaxial connector and the other
end of the coaxial connector to the remote network equipment through a 75-ohm
E1 trunk cable, if cable extension is needed.