Adaptec 412R User Guide - Page 60

Front Bezel

Page 60 highlights

DuraStor 412R/6320SS/7320SS Installation and User's Guide Front Bezel The front bezel (Figure 5-1) houses the status LEDs, drive LEDs, and alarm reset button. When the front bezel is removed, you can access the disk drives. The front bezel can be installed or removed without interruption to current system activities. Embedded within the front bezel is the electronic package that provides the communication with the microprocessor. The microprocessor communicates with the RAID controllers, SAF-TE Environmental Processors (SEPs), and the disk drives in the storage subsystem. It passes that information to the front bezel channel mode and drive status LEDs, and the Disk Array Administrator firmware-based software. Power is applied to the front bezel through an edge connector, where a control circuit monitors the bezel for proper connection. When the bezel is properly installed and power is applied to the storage subsystem, the bezel is immediately energized. Drive Activity LEDs Status LEDs Alarm Reset Button Figure 5-1 Removable Front Bezel For instructions on removing and replacing the front bezel, see page 2-3. 5-2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210

5-2
DuraStor 412R/6320SS/7320SS Installation and User’s Guide
Front Bezel
The front bezel (
Figure 5-1
) houses the status LEDs, drive LEDs,
and alarm reset button. When the front bezel is removed, you can
access the disk drives. The front bezel can be installed or removed
without interruption to current system activities.
Embedded within the front bezel is the electronic package that
provides the communication with the microprocessor. The
microprocessor communicates with the RAID controllers, SAF-TE
Environmental Processors (SEPs), and the disk drives in the storage
subsystem. It passes that information to the front bezel channel
mode and drive status LEDs, and the Disk Array Administrator
firmware-based software.
Power is applied to the front bezel through an edge connector,
where a control circuit monitors the bezel for proper connection.
When the bezel is properly installed and power is applied to the
storage subsystem, the bezel is immediately energized.
Figure 5-1
Removable Front Bezel
For instructions on removing and replacing the front bezel, see
page 2-3
.
D
rive Activi
ty LEDs
Status L
EDs
Alarm Re
set Button