Adaptec 412R User Guide - Page 65

Replacing the Battery

Get Adaptec 412R - DuraStor Storage Enclosure PDF manuals and user guides
UPC - 760884139691
View all Adaptec 412R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Understanding and Maintaining Components Replacing the Battery 1 Use your screwdriver to loosen and remove the screws that secure the top of the canister to the bottom. There are four screws on each side of the canister and two on the bottom-10 screws in total. 2 Pull the top of the canister away from the bottom, and set it aside. 3 Align the battery as shown in Figure 5-5 and place it in the canister between the battery posts. Figure 5-5 Installing the Battery 4 Plug the battery cable into the white, three-pronged connector on the DuraStor RAID controller. See Figure 5-5. 5 Place the battery cover over the battery, lining up the three screw holes with the three battery posts. 6 Use three washer and screw sets to attach the battery cover to the canister. Do not over tighten the screws. 7 Close the canister and replace the screws. 5-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
5-7
Understanding and Maintaining Components
Replacing the Battery
1
Use your screwdriver to loosen and remove the screws that
secure the top of the canister to the bottom. There are four
screws on each side of the canister and two on the bottom—10
screws in total.
2
Pull the top of the canister away from the bottom, and set it
aside.
3
Align the battery as shown in
Figure 5-5
and place it in the
canister between the battery posts.
Figure 5-5
Installing the Battery
4
Plug the battery cable into the white, three-pronged connector
on the DuraStor RAID controller. See
Figure 5-5
.
5
Place the battery cover over the battery, lining up the three
screw holes with the three battery posts.
6
Use three washer and screw sets to attach the battery cover to
the canister.
Do not
over tighten the screws.
7
Close the canister and replace the screws.