Home » Brother International Manuals » Sewing Machines » Brother International BAS-375E » Manual Viewer

Brother International BAS-375E Instruction Manual - English - Page 10

Installing the needle plates

Get Brother International BAS-375E PDF manuals and user guides

View all Brother International BAS-375E manuals

Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

3. Installing the needle plates * For BAS-370E, 375E i o !0 Chapter 3 INSTALLATION r u r r i t w * For BAS-364E, 366E y q e !1 q w e 1. Loosen the bolts q, and then pull the needle plate support bases w to the outside. 2. Secure the needle plate support bases w by tightening the bolts q and the bolts e. 3. Install the needle plate support brackets r to the needle plate support bases w by tightening the bolts t from below. * For the BAS-366E and BAS-375E, install the needle plate support brackets y to the needle plate support brackets r with the bolts u. 4. Place the screw holes in the left needle plate i, center needle plate o and right needle plate !0 on top of the needle plate support hases w so that the screw holes are aligned, and then secure them by tightening the screws. * For the BAS-364E, install the center needle plate !1 only. BAS-364E, 366E, 370E, 375E 4

Section	Page
Go to Instruction Manual Top Page	1
PL	2
Contents	6
Chapter 1 NAME OF MAJOR PARTS	7
Chapter 2 SPECIFICATIONS	8
Chapter 3 INSTALLATION	9
1.Connecting the ground wire	9
2. Positioning	9
3. Installing the needle plates	10
4. Installing the work clamp hinge	11
5. Installing the arm motor cover	11
6. Installing the foot switch	12
7. Installing the programmer box	12
8. Installing the programmer	12
9. Installing the spool stand	13
10. Preparation of cassette	13
11. Lubrication	14
12. Draining oil	15
13. Applying grease	16
14. Adjusting the air pressure	17
Chapter 4 CORRECT OPERATION	18
1. Turning the pulley by hand	18
2. Installing the needle	18
3. Threading the upper thread	19
4. Winding the lower thread	20
5. Installing the bobbin case	21
6. Thread tension	22
7. Work clamp	23
8. Selecting intermittent feed or contimuous feed	24
Chapter 5 OPERATING PROCEDURE	25
1. Part names and functions of the operation panel	25
2. Using the floppy disk	27
3. Using the program R/W (Read/Write) switch	29
4. Using the emergency stop switch	30
5. Adjusting the sewing speed control	31
6. Changing the X-scale and Y-scale settings	31
7. Using the TEST switch (Checking the sewing pattern)	32
8. Using the STEP BACK switch	33
9. Using single split mode	34
10. Using the bobbin thread counter	35
11. Using production counter	36
12. Shifting a stitch pattern	37
Chapter 6 SEWING	38
1. Before starting sewing....	38
2. Sewing operation	39
Chapter 7 STANDARD ADJUSTMENTS	40
1. Needle and rotary hook timing	40
2. Adjusting the needle bar height	41
3. Adjusting the needle clearance	41
4. Adjusting the presser foot	42
5. Changing the presser foot lift amount	43
6. Replacing the fixed knife and movable knife	44
7. Adjusting the inner ratary hook bobbin case holder position	45
8. Checking the input voltage	46
9. Clearing all memory settings	46
Chapter 8 DEVICES	47
1. Needle thread presser	47
2. Beam sensor-type needle thread breakage detector	47
3. Two-stage thread tension mechanism (Option)	48
4. Stepping foot control mechanism	48
5. Needle cooler (Air bag specification - Option)	49
6. Installing the bottom plunger (Option)	49
7. Jig pattern sensor (Option)	50
8. Sub clamp (BAS-370E, 375E only)	51
Chapter 9 CLEANING AND INSPECTION	53
1. Rotary hook	53
2. Eye guard	53
3. Checking the needle	54
Chapter 10 DIP SWITCH	55
1. Panel DIP switch functions	55
2. DIP switches inside the control box	56
Chapter 11 CHANGING SPECIAL FUNCTIONS AND USING THE MEMORY SWITCHES	58
Chapter 12 ERROR CODE	63
Chapter 13 TROUBLESHOOTING	65
OPERATION FLOW CHART	67