Brother International BAS-375E Instruction Manual - English - Page 51

Sub clamp (BAS-370E, 375E only

Get Brother International BAS-375E PDF manuals and user guides View all Brother International BAS-375E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

Chapter 8 DEVICES 8. Sub clamp (BAS-370E, 375E only) This is used when the standard clamp alone cannot hold the work piece properly. When using the sub clamp, set DIP switch E-2 on the main circuit board. D B' E C Main circuit board r First-stage Second-stage 12345678 12345678 A B q w e Selecting sub-work clamp operation Note Always be sure to turn off the power when changing the DIP switch settings. G After sewing, the standard work clamp q, presser foot w and sub clamp e are raised simultaneously, but they are lowered separately as shown below. The movement can be changed by means of a DIP switch. (The work clamp lift switch r is a two-stage switch.) G When DIP switch A-2 is OFF * When the first-stage switch is ON, work clamp q, stepping foot w and sub clamp e are lowered. G When DIP switch A-2 is ON * When the first-stage switch is ON, the work clamp q and stepping foot w are lowered. Then, when the secondstage switch is ON, the sub clamp e is lowered. BAS-364E, 366E, 370E, 375E 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
45
BAS-364E, 366E, 370E, 375E
Chapter 8
DEVICES
Selecting sub-work clamp operation
Note
Always be sure to turn off the power when changing the DIP switch settings.
●
After sewing, the standard work clamp
q
, presser foot
w
and sub clamp
e
are raised simultaneously, but they are
lowered separately as shown below. The movement can be changed by means of a DIP switch. (The work clamp lift
switch
r
is a two-stage switch.)
●
When DIP switch A-2 is OFF
* When the first-stage switch is ON, work clamp
q
, stepping foot
w
and sub clamp
e
are lowered.
●
When DIP switch A-2 is ON
* When the first-stage switch is ON, the work clamp
q
and stepping foot
w
are lowered. Then, when the second-
stage switch is ON, the sub clamp
e
is lowered.
8. Sub clamp (BAS-370E, 375E only)
This is used when the standard clamp alone cannot hold the work piece properly.
When using the sub clamp, set DIP switch E-2 on the main circuit board.
12345678
12345678
A
B
r
q
w
e
First-stage
Second-stage
B’
C
D
E
Main circuit
board