Brother International BAS-375E Instruction Manual - English - Page 24

Selecting intermittent feed or contimuous feed

Get Brother International BAS-375E PDF manuals and user guides View all Brother International BAS-375E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Chapter 4 CORRECT OPERATION 8. Selecting intermittent feed or continuous feed q CAUTION Turn off the power switch before starting any cleaning work, otherwise the machine may operate if the foot switch is depressed by mistake, which could result in injury. Check the model number w on the model plate on the w side of the sewing machine arm q. 1. When the model number is either BAS-364E-02, BAS- 366E-02, BAS-370E-02, BAS-375E-02, select intermittent feed or continuous feed as follows: Note If DIP switch C-8 on the main circuit board is set to D ON when link (L) is not reattached to the intermittent feed shaft, intermittent feed will be selected instead of continuous feed. B' G When selecting intermittent feed (400 - 2000 rpm), E set DIP switch C-8 on the main circuit board to OFF. G When using continuous feed (400 - 3200 rpm), it is C impossible to operate the presser foot intermittently. Remove the stud screw e, and reattach link (L) to the intermittent feed shaft t. Then, set DIP switch Main circuit board C-8 on the main circuit board to ON. Note Be sure to turn the power off before replacing link (L) r, otherwise injury or damage may result. * If DIP switch C-8 on the main circuit board is set to ON while the presser foot is operating intermittently, intermittent feed (400 - 2,000 rpm) t will be selected instead of continuous feed (400 - 3,200 rpm). e r For models other than those above 2. When the model number is either BAS-366E-01, BAS- 364E-01, BAS-364E-11, BAS-370E-01, BAS-375E-01, continuous feed can not be used. Never change the setting of DIP switch as described in step 1.. Note If you operate a machine with one of the above model numbers at continuous feed, problems such machine seizure will occur. BAS-364E, 366E, 370E, 375E 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
18
Chapter 4
CORRECT OPERATION
BAS-364E, 366E, 370E, 375E
8. Selecting intermittent feed or continuous feed
Turn off the power switch before starting any
cleaning work, otherwise the machine may
operate if the foot switch is depressed by
mistake, which could result in injury.
CAUTION
Check the model number
w
on the model plate on the
side of the sewing machine arm
q
.
1. When the model number is either BAS-364E-02, BAS-
366E-02, BAS-370E-02, BAS-375E-02, select
intermittent feed or continuous feed as follows:
Note
If DIP switch C-8 on the main circuit board is set to
ON when link (L) is not reattached to the intermittent
feed shaft, intermittent feed will be selected instead of
continuous feed.
●
When selecting intermittent feed (400 - 2000 rpm),
set DIP switch C-8 on the main circuit board to OFF.
●
When using continuous feed (400 - 3200 rpm), it is
impossible to operate the presser foot intermittently.
Remove the stud screw
e
, and reattach link (L) to
the intermittent feed shaft
t
. Then, set DIP switch
C-8 on the main circuit board to ON.
Note
Be sure to turn the power off before replacing
link (L)
r
, otherwise injury or damage may result.
* If DIP switch C-8 on the main circuit board is set
to ON while the presser foot is operating
intermittently, intermittent feed (400 - 2,000 rpm)
will be selected instead of continuous feed (400 -
3,200 rpm).
For models other than those above
2. When the model number is either BAS-366E-01, BAS-
364E-01, BAS-364E-11, BAS-370E-01, BAS-375E-01,
continuous feed can not be used. Never change the
setting of DIP switch as described in step 1..
Note
If you operate a machine with one of the above model
numbers at continuous feed, problems such machine
seizure will occur.
q
w
t
e
r
B
’
C
D
E
Main circuit
board