Brother International BAS-375E Instruction Manual - English - Page 18

CORRECT OPERATION, 1. Turning the pulley by hand, 2. Installing the needle

Get Brother International BAS-375E PDF manuals and user guides View all Brother International BAS-375E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Chapter 4 CORRECT OPERATION Chapter 4 CORRECT OPERATION 1. Turning the pulley by hand CAUTION If the power switch and air need to be left on when carrying out some adjustment, be extremely careful to observe all safety precautions. w r e q After pressing the hand pulley q in, it can then be turned by hand. To return the hand pulley q, pull the lever w toward you. * Furthermore, the hand pulley q will automatically return to its original position at the sewing start and when the work clamp is raised and lowered. Note Do not touch the hand pulley q, lever w, work clamp lifter arm e or cylinder r while the machine is operating and when the work clamp is being raised and lowered, otherwise injury may result. 2. Installing the needle CAUTION Turn off the power switch at the following times, otherwise the machine may operate if the start switch is pressed by mistake, which could result in injury. G When replacing the needle Loosen set screw q. Fully insert the needle w with the groove facing the front, and then retighten set screw q. Note G Always make sure that the needle w is fully inserted facing the front. G If the needle is installed incorrectly, problems such q as needle breakage may occur. w BAS-364E, 366E, 370E, 375E 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
12
Chapter 4
CORRECT OPERATION
BAS-364E, 366E, 370E, 375E
Chapter 4
CORRECT OPERATION
1.Turning the pulley by hand
CAUTION
Turn off the power switch at the following times, otherwise the machine may operate if the start switch is
pressed by mistake, which could result in injury.
●
When replacing the needle
CAUTION
If the power switch and air need to be left on when carrying out some adjustment, be extremely careful to
observe all safety precautions.
2. Installing the needle
After pressing the hand pulley
q
in, it can then be turned
by hand. To return the hand pulley
q
, pull the lever
w
toward you.
*
Furthermore, the hand pulley
q
will automatically return
to its original position at the sewing start and when the
work clamp is raised and lowered.
Note
Do not touch the hand pulley
q
, lever
w
, work clamp
lifter arm
e
or cylinder
r
while the machine is
operating and when the work clamp is being raised
and lowered, otherwise injury may result.
w
r
e
q
Loosen set screw
q
. Fully insert the needle
w
with the
groove facing the front, and then retighten set screw
q
.
Note
●
Always make sure that the needle
w
is fully inserted
facing the front.
●
If the needle is installed incorrectly, problems such
as needle breakage may occur.
q
w