Brother International BAS-375E Instruction Manual - English - Page 21

Installing the bobbin case

Get Brother International BAS-375E PDF manuals and user guides View all Brother International BAS-375E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Chapter 4 CORRECT OPERATION w A q B Note If the bobbin thread is wound unevenly onto the bobbin, loosen nut q, and turn thread tension stud w to adjust so that the thread is wound evenly. If the bobbin is wound as in Fig. A, turn the stud clockwise, if Fig. B, turn the stud counterclockwise. 5. Installing the bobbin case CAUTION If the power switch needs to be left on when carrying out replacing the bobbin, be extremely careful to observe all safety precautions. The machine may operate if the foot switch is depressed by mistake, which could result in injury. (ex. Continuing sewing from a stopping point) Note G Do not replace the bobbin or put your hand close to the bobbin case while the machine is operating. G Do not operate the machine while replacing the bobbin, otherwise injury and damage could result. r t e q w 1. Raise the bobbin case latch w, and then remove the bobbin case q from inside the rotary hook at the front of the machine head. 2. While the bobbin case latch w is still lowered, remove the bobbin e from the bobbin case q. 3. Place a new bobbin with the bobbin thread already wound on into the bobbin case q, and then pass the thread through the slot r and pull it out from the thread hole t. BAS-364E, 366E, 370E, 375E 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
15
BAS-364E, 366E, 370E, 375E
Chapter 4
CORRECT OPERATION
Note
If the bobbin thread is wound unevenly onto the bobbin,
loosen nut
q
, and turn thread tension stud
w
to adjust
so that the thread is wound evenly. If the bobbin is
wound as in Fig. A, turn the stud clockwise, if Fig. B,
turn the stud counterclockwise.
5. Installing the bobbin case
If the power switch needs to be left on when carrying out replacing the bobbin, be extremely careful to
observe all safety precautions.
The machine may operate if the foot switch is depressed by mistake, which could result in injury.
(ex. Continuing sewing from a stopping point)
CAUTION
Note
●
Do not replace the bobbin or put your hand close to the bobbin case while the machine is operating.
●
Do not operate the machine while replacing the bobbin, otherwise injury and damage could result.
1. Raise the bobbin case latch
w
, and then remove the bobbin case
q
from inside the rotary hook at the front of the
machine head.
2. While the bobbin case latch
w
is still lowered, remove the bobbin
e
from the bobbin case
q
.
3. Place a new bobbin with the bobbin thread already wound on into the bobbin case
q
, and then pass the thread
through the slot
r
and pull it out from the thread hole
t
.
w
q
e
q
w
r
t
B
A