Brother International MFC 3100C Users Manual - English - Page 193

Did You Change Blck? 1. Yes 2. No, Cleaning, Please, Warning

Page 193 highlights

6 Hold the new ink cartridge as shown in the illustration, and then peel the sealing tape from the side of the ink cartridge. Carefully peel the tape in the direction away from you. Peel in the direction away from you! Opening Note To prevent spilling ink and staining your hands and clothing, remove the sealing tape gently. 7 Each color has its own correct position. Insert each new ink cartridge into the carriage. 8 After installing the ink cartridges, close the top cover and control panel cover. Your MFC prepares for a "head cleaning" and goes online. The LCD prompts you to verify a new ink cartridge was inserted for each color you removed. Example: DID YOU CHANGE BLCK? 1. YES 2. NO. If the ink cartridge you installed is not a brand new one, please make sure to select 2. 9 For each new cartridge, press 1 on the dial pad to reset the ink dot counter for that color automatically. (The ink dot counter enables the MFC to notify you when a color is running low.) The MFC will enter a cleaning cycle for approximately 3 minutes for each replaced cartridge. The LCD alternately shows CLEANING and PLEASE WAIT. When the MFC completes the cleaning cycle, the LCD returns to Standby mode (date and time). WARNING If ink gets in your eyes, irrigate them with water immediately and consult a doctor if you are concerned. T R O U B L E S H O O T I N G A N D R O U T I N E M A I N T E N A N C E 20 - 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210

TROUBLESHOOTING AND ROUTINE MAINTENANCE
20 - 18
6
Hold the new ink
cartridge as shown in
the illustration, and
then peel the sealing
tape from the side of
the ink cartridge.
Carefully peel the tape
in the direction away
from you.
7
Each color has its own correct position. Insert each new ink cartridge into the
carriage.
8
After installing the ink cartridges, close the top cover and control panel cover.
Your MFC prepares for a
head cleaning
and goes online. The LCD prompts
you to verify a new ink cartridge was inserted for each color you removed.
Example:
DID YOU CHANGE BLCK? 1. YES 2. NO
.
If the ink cartridge you installed is not a brand new one, please make sure to
select 2.
9
For each new cartridge, press
1
on the dial pad to reset the ink dot counter for
that color automatically. (The ink dot counter enables the MFC to notify you
when a color is running low.)
The MFC will enter a cleaning cycle for approximately 3 minutes for each
replaced cartridge. The LCD alternately shows
CLEANING
and
PLEASE
WAIT
.
When the MFC completes the cleaning cycle, the LCD returns to Standby mode
(date and time).
WARNING
If ink gets in your eyes, irrigate them with water immediately and consult a
doctor if you are concerned.
Note
To prevent spilling ink and staining your hands and clothing, remove the
sealing tape gently.
Opening
Peel in the direction
away from you!