Cisco ESR10008 Hardware Installation Guide - Page 112
Replacing a DC PEM, Setting DC Power Switch to the Off Position
![]() |
UPC - 746320761510
View all Cisco ESR10008 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 112 highlights
Removing and Replacing Field-Replaceable Units Chapter 5 Maintaining the Cisco 10008 Router Replacing a DC PEM Use the following procedure to replace a DC PEM: Figure 5-21 Setting DC Power Switch to the Off Position POWER FAULT MISWIRE POWER FAULT MISWIRE LOOP ALARM CARRIER RX TX LINK FANS OK FAFILAUNRE FMAFUILALUNTRI-E WrbseyemhsdteoeonvmnahelsoaihtnnCusduwtAdnarUodepwTeppnIrliaOntcwwgNeioltmlhmoiescnincftauumntre.utsrsaotyr, FAIL FAIL FAIL FAIL 1 C1I0S0C0O0 2 C1I0S0C0O0 3 C1I0S0C0O0 4 CC161I0CS00T0C003O00 FAIL LOOP CARALRAIERRM LOOP CARALRAIERRM 0 PO0RT0 CA ALARLMOOP 1 PO1RT1 2 PO2RT2 3 PO3RT3 4 PO4RT4 5 PO5RT5 0A PROCESSOR ONLY0B CISCO 10000 CISCO 10000 CONSOLE AUX ELAICTNHTKIEVRITNYET CONSOLE AUX ELAICTNHTKIEVRITNYET 5 CC161I0CS00T0C003O00 FAIL 6 CC161I0CS00T0C003O00 FAIL 7 CC161I0CS00T0C003O00 FAIL LOOP CARALRAIERRM LOOP CARALRAIERRM LOOP CARALRAIERRM PO0RT0 CA ALARLMOOP PO0RT0 CA ALARLMOOP PO0RT0 CA ALARLMOOP ACTIVITY LINK ACTIVITY LINK ALARMS ALARMS PO1RT1 PO2RT2 PO1RT1 PO2RT2 PO1RT1 PO2RT2 CRITICMAALJORMINOR ACO PO3RT3 PO3RT3 PO3RT3 PO4RT4 PO4RT4 PO4RT4 PO5RT5 PO5RT5 PO5RT5 RX TX CARRIER CRITICMAALJORMINOR ACO FAIL FAIL FAIL FAIL 8 C1I0S0C0O0 SLOT 0 STATUFSAIL BITS SLOT 0 STATUFSAIL BITS CH OC-12-DSO SM-IR GIGABIT ETHERNET 6XCT3-DS0 6XCT3-DS0 6XCT3-DS0 PERFORMANCE ROUTING ENGINE P/N ESR-PRE3 PERFORMANCE ROUTING ENGINE P/N ESR-PRE3 6XCT3-DS0 6XCT3-DS0 POWER FAULT MISWIRE PROCESSOR ONLY OC-12/STM-4 POS SM-IR 30019 Step 1 Step 2 Remove the front cover if necessary (see Front Cover Procedures, page 5-4). Set the power switch to the off (0) position. If you have redundant PEMs, set only the power switch of the PEM you are replacing to the off (0) position (the example in Figure 5-21 shows the top PEM in the off position). Caution Do not power off both of the DC PEMs in a redundant system, or the system shuts and down all data traffic stops. Only power off the DC PEM you are replacing. 5-20 Cisco 10008 Router Hardware Installation Guide OL-0659-13
![](/manual_guide/products/cisco-10008-hardware-installation-guide-4642de6/112.png)