Cisco ESR10008 Hardware Installation Guide - Page 55

Connecting the Chassis to Ground

Get Cisco ESR10008 - 10000 Modular Expansion Base PDF manuals and user guides
UPC - 746320761510
View all Cisco ESR10008 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Chapter 3 Installing the Cisco 10008 Router Connecting the Chassis to Ground Note The cable management bracket consists of two pieces (the cable guide and channel), and is shipped assembled. If you want to use the cable guide only, you can remove the channel by loosening the captive screws before attaching the cable guide to the chassis. Figure 3-11 Attaching Cable Management Bracket POWER FAULT MISWIRE POWER FAULT MISWIRE RX TX CARRIER LOOP ALARM CARRIER RX TX LINK FANS OK FAFILAUNRE FMAFIULALUNTRI-E WrbseyemhsdetoeonvmnahelsoaihtnnCusduwtAdnarUodepwTeppnIrliaOntcwwgNeioltmlhmoiescnincftauumntre.utsrsaotyr, 1 CISCO 10000 2 CISCO 10000 3 CISCO 10000 4 CISCO 10000 FAIL FAIL FAIL FAIL LOOP CARALRAIERRM LOOP CARALRAIERRM 0 0 1 1 2 2 SSLLOOTT01 SSLLOOTT01 0A PROCESSOR ONLY0B CISCO 10000 CISCO 10000 CONSOLE AUX ELAICTNHTKIEVRITNYET CONSOLE AUX ELAICTNHTKIEVRITNYET LOOP CARALRAIERRM LOOP CARALRAIERRM LOOP CARALRAIERRM FAIL FAIL FAIL 5 CISCO 10000 0 6 CISCO 10000 0 7 CISCO 10000 0 1 1 1 3 3 2 2 2 4 4 5 5 3 3 3 4 4 4 5 5 5 FAIL 8 CISCO 10000 ACO CMRAIJTOICRAL MINOR SFATAILTUS ACO CMRAIJTOICRAL MINOR SFATAILTUS PROCESSOR ONLY OC-12/STM-4 POS SM-IR 6XCT3-DS0 6XCT3-DS0 6XCT3-DS0 PERFORMANCE ROUTING ENGINE PERFORMANCE ROUTING ENGINE 6XCT3-DS0 6XCT3-DS0 CH OC-12-DSO SM-IR GIGABIT ETHERNET 76215 Step 3 Step 4 Step 5 Attach the cable management bracket to the bottom of the chassis if you are using it (Figure 3-11). Check that all - Ejector levers are in the closed position. - PRE and line card captive screws are tight. Go to the "Connecting the Chassis to Ground" section on page 3-13 to continue the installation. Connecting the Chassis to Ground Connecting the Cisco 10008 chassis to earth ground is required for all DC powered installations, and any AC powered installation where compliance with Telcordia (formerly Bellcore) grounding requirements is necessary. Have the recommended tools and supplies available before you begin this procedure (see Table 3-1). Warning Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 93 OL-0659-13 Cisco 10008 Router Hardware Installation Guide 3-13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
3-13
Cisco 10008 Router Hardware Installation Guide
OL-0659-13
Chapter 3
Installing the Cisco 10008 Router
Connecting the Chassis to Ground
Note
The cable management bracket consists of two pieces (the cable guide and channel), and is
shipped assembled. If you want to use the cable guide only, you can remove the channel by
loosening the captive screws before attaching the cable guide to the chassis.
Figure 3-11
Attaching Cable Management Bracket
Step 3
Attach the cable management bracket to the bottom of the chassis if you are using it (
Figure 3-11
).
Step 4
Check that all
–
Ejector levers are in the closed position.
–
PRE and line card captive screws are tight.
Step 5
Go to the
“Connecting the Chassis to Ground” section on page 3-13
to continue the installation.
Connecting the Chassis to Ground
Connecting the Cisco
10008 chassis to earth ground is required for all DC
powered installations, and any
AC powered installation where compliance with Telcordia (formerly Bellcore) grounding requirements
is necessary. Have the recommended tools and supplies available before you begin this procedure (see
Table 3-1
).
Warning
Never defeat the ground conductor or operate the equipment in the absence of a suitably installed
ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are
uncertain that suitable grounding is available.
Statement 93
76215
1
3
2
4
0A
PROCESSOR ONLY
0B
5
6
7
8
PROCESSOR ONLY
POWER
FAULT
MISWIRE
POWER
FAULT
MISWIRE
CISCO
10000
GIGABIT ETHERNET
CISCO
10000
CH OC-12-DSO SM-IR
CISCO
10000
6XCT3–DS0
0
5
4
3
2
1
CISCO
10000
6XCT3–DS0
0
5
4
3
2
1
FAIL
PERFORMANCE ROUTING ENGINE
STATUS
ACO
CRITICAL
MINOR
MAJOR
FAIL
PERFORMANCE ROUTING ENGINE
STATUS
ACO
CRITICAL
MINOR
MAJOR
CISCO
10000
6XCT3–DS0
0
5
4
3
2
1
CISCO
10000
6XCT3–DS0
0
5
4
3
2
1
CISCO
10000
6XCT3–DS0
0
5
4
3
2
1
CISCO
10000
OC–12/STM–4 POS SM–IR
CISCO
10000
CISCO
10000
FANS
OK
FAN
FAILURE
MULTI-
FAN
FAILURE
When hot swapping this fan tray,
removal and replacement must
be done in under two minutes or
system shutdown will occur.
CAUTION