Home » Cisco Manuals » Bridges & Routers » Cisco ESR10008 » Manual Viewer

Cisco ESR10008 Hardware Installation Guide - Page 82

Using the System Configuration Dialog, Basic System Configuration Procedure, Ctrl-C, setup

UPC - 746320761510

Add to My Manuals
Save this manual to your list of manuals

Page 82 highlights

Configuring the Cisco 10008 Router at Startup Chapter 4 Starting and Configuring the Router Using the System Configuration Dialog Use the System Configuration Dialog to help you perform a basic configuration. Proceed through the dialog by answering questions and then pressing the Enter key. In most cases, you can get additional information by entering a question mark (?). Throughout the dialog, default values are shown in square brackets [ ]. Tip If you have experience using Cisco routers, consider configuring the router by using the procedure described in the "Basic Configuration in Global Configuration Mode" section on page 4-6. To cancel the configuration dialog, press Ctrl-C, or you can let the dialog help you perform one of two configuration types: • Basic configuration setup configures only enough connectivity for management of the system. • Extended setup asks you to configure each interface and is not appropriate for configuring the Cisco 10008 router. For more information, see the Cisco IOS Configuration Fundamentals Configuration Guide. You can run the setup facility any time you are at the enable prompt (#) by entering the command setup. Basic System Configuration Procedure Use the following procedure to perform a basic configuration using the System Configuration Dialog: Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Step 9 The dialog starts by asking if you want to continue with the configuration dialog. Enter Yes. To return to the enable prompt, enter No. --- System Configuration Dialog --Continue with configuration dialog? [yes/no]: yes Enter Yes to perform a basic management setup. Enter No to perform an extended configuration setup. Would you like to enter basic management setup? [yes/no]: yes Specify a hostname. The hostname becomes part of the Cisco IOS prompt. Enter host name [Router]: my-router Specify a secret password. It appears in encrypted form in the configuration file. Enter enable secret: my_secret Specify the enable password. It is used if you did not assign a secret one. Enter enable password: my_password Specify the password to use for telnet sessions. Enter virtual terminal password: my_vt At the configure system management prompt, enter No. Configure System Management? [yes/no]: no If you want to access the router using SNMP, enter Yes at the prompt: Configure SNMP Network Management? [yes]: yes Specify an SNMP community string. Cisco 10008 Router Hardware Installation Guide 4-4 OL-0659-13

Section	Page
Cisco10008 Router Hardware Installation Guide	1
Contents	3
Preface	7
Document Version History	7
Audience	8
Purpose	8
Document Organization	8
Document Conventions	8
Notes and Cautions	9
Safety Warnings	9
Related Documentation	11
Obtaining Documentation	11
Cisco.com	11
Ordering Documentation	12
Documentation Feedback	12
Obtaining Technical Assistance	12
Cisco Technical Support Website	12
Submitting a Service Request	13
Definitions of Service Request Severity	13
Obtaining Additional Publications and Information	14
Cisco 10008 Router Overview	15
Cisco 10008 Router Features	16
Cisco 10008 Router Software	17
Minimum Software Releases for the Cisco 10008 Router	17
Cisco 10008 Router Hardware Description	17
Blower Module	20
Power Entry Modules	20
Line Card and PRE Module Compartment	22
Performance Routing Engine	22
Connector Ports	23
PCMCIA Card Slots	24
PRE LED Indicators and Switches	24
Alphanumeric Display	25
Disposing of the PRE	25
Preparing for Installation	27
Site Planning	27
Cisco Professional Installation	28
Site Selection Guidelines	28
Site Environmental Requirements	28
Heat Dissipation	28
Physical Characteristics	29
Floor Loading Considerations	29
Site Power Requirements	29
Electrical Service Requirements	30
Electrical Circuit Requirements	30
Site Cabling Guidelines	31
Interference Considerations	32
Asynchronous Terminal Connections	32
Ethernet Connections	32
Setting Up Fiber-Optic Connections	33
Interference Considerations	33
Rack-Mounting and Location Guidelines	34
Rack Selection Guidelines	34
Rack Configuration Guidelines	34
Rack Placement Guidelines	35
Site Planning Checklist	37
Safety	37
Preventing Electrostatic Discharge Damage	38
Electrical Safety	39
Receiving the Cisco 10000 Series Router	40
Chassis-Lifting Guidelines	41
Required Tools and Equipment	42
Verifying Contents After Unpacking	42
Installing the Cisco 10008 Router	43
Installation Methods	43
Rack-Mounting the Chassis	44
General Rack Installation Guidelines	44
Flush-Mounting in a 19-Inch Rack	45
Center-Mounting in a 19-Inch Rack	47
Center-Mounting in a 23-Inch Rack	49
Non-Rack Installation	53
Connecting the Chassis to Ground	55
Recommended Tools and Supplies	56
Attaching the Grounding Cable	56
Connecting DC Power to the Cisco 10008 Router	59
Recommended Tools and Supplies	60
Connecting AC Power to the Cisco 10008 Router	64
Connecting Alarm Indicators	68
Connecting a Video Terminal to the PRE Console Port	72
Connecting Network Management and Signal System Cables	74
Ethernet Network Management Cable Connections	74
Connecting to a 10BASE-T Ethernet Network	74
Connecting to a 100BASE-T Ethernet Network	75
Auxiliary Modem Connection	77
Data Network Cable Connections	77
Starting and Configuring the Router	79
Powering On the System	79
Configuring the Cisco 10008 Router at Startup	80
Startup Display	81
Basic Configuration Using the Setup Facility	81
Using the System Configuration Dialog	82
Basic System Configuration Procedure	82
Basic Configuration in Global Configuration Mode	84
Formatting Flash Memory Cards and Disks	84
Managing the File Systems	85
File Systems	85
Copying the Startup Configuration to the Running Configuration	86
Managing Configuration Files Larger than NVRAM	86
Compressing the Configuration File	86
Relocating the Configuration to a Flash Disk	87
Managing System Boot Parameters	87
Changing the Configuration Register Settings	88
Configuration Register Settings	88
Predeployment Testing	89
Troubleshooting Installation Problems	90
General Troubleshooting Tips	90
Troubleshooting Ethernet Connections	91
Troubleshooting the Console Port Serial Connection	92
Maintaining the Cisco 10008 Router	93
Required Maintenance Tools	95
Shutting Down the System	95
Backing Up the PCMCIA Card	95
Removing and Replacing Field-Replaceable Units	95
Front Cover Procedures	96
Removing the Front Cover	96
Replacing the Front Cover	98
Replacing the Air Filter	99
Replacing an Air Filter in a Chassis that Uses a Filter Tray	99
Replacing an Air Filter in a Chassis with Release Tabs	101
Replacing the Blower Module	102
Installing Power Entry Modules	104
Installing a Second DC PEM	104
Replacing a DC PEM	112
Installing a Second AC PEM	116
Replacing an AC PEM	120
Connecting Alarm Indicators	124
Removing and Replacing the PRE	128
Removing and Installing a PCMCIA Flash Memory Card	136
Upgrading SDRAM on the PRE	138
Removing and Installing DIMMS	139
Troubleshooting the DIMM Installation	141
Technical Specifications	143
Repacking the Box	147
Glossary	151

Match case Limit results 1 per page

4-4

Cisco 10008 Router Hardware Installation Guide

OL-0659-13

Chapter 4

Starting and Configuring the Router

Configuring the Cisco 10008 Router at Startup

Using the System Configuration Dialog

Use the System Configuration Dialog to help you perform a basic configuration. Proceed through the

dialog by answering questions and then pressing the Enter key. In most cases, you can get additional

information by entering a question mark (?). Throughout the dialog, default values are shown in square

brackets [ ].

Tip

If you have experience using Cisco routers, consider configuring the router by using the procedure

described in the

“Basic Configuration in Global Configuration Mode” section on page 4-6

To cancel the configuration dialog, press

Ctrl-C

, or you can let the dialog help you perform one of two

configuration types:

•

Basic configuration setup configures only enough connectivity for management of the system.

•

Extended setup asks you to configure each interface and is not appropriate for configuring the Cisco

10008 router. For more information, see the

Cisco IOS Configuration Fundamentals Configuration

Guide

You can run the setup facility any time you are at the enable prompt (#) by entering the command

setup

Basic System Configuration Procedure

Use the following procedure to perform a basic configuration using the System Configuration Dialog:

Step 1

The dialog starts by asking if you want to continue with the configuration dialog. Enter

Yes

. To return

to the enable prompt, enter

--- System Configuration Dialog ---

Continue with configuration dialog? [yes/no]:

yes

Step 2

Enter

Yes

to perform a basic management setup. Enter

to perform an extended configuration setup.

Would you like to enter basic management setup? [yes/no]:

yes

Step 3

Specify a hostname. The hostname becomes part of the Cisco IOS prompt.

Enter host name [Router]:

my-router

Step 4

Specify a secret password. It appears in encrypted form in the configuration file.

Enter enable secret:

my_secret

Step 5

Specify the enable password. It is used if you did not assign a secret one.

Enter enable password:

my_password

Step 6

Specify the password to use for telnet sessions.

Enter virtual terminal password:

my_vt

Step 7

At the configure system management prompt, enter

Configure System Management? [yes/no]:

Step 8

If you want to access the router using SNMP, enter

Yes

at the prompt:

Configure SNMP Network Management? [yes]:

yes

Step 9

Specify an SNMP community string.