Dell Brocade G620 Hardware Installation Guide - Page 30

Flush-front mounting, Attaching the front brackets, CAUTION

Get Dell Brocade G620 PDF manuals and user guides View all Dell Brocade G620 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Flush-front mounting Flush-front mounting CAUTION The device must be turned off and disconnected from the fabric during this procedure. NOTE The illustrations in the rack installation procedures show a 1U device, but the instructions are the same for a 2U device. The illustrations in the rack installation procedures are for reference only and may not show the actual device. Complete the following tasks to install the device in a four-post rack: 1. Attaching the front brackets on page 30 2. Attaching the extension brackets to the device on page 31 3. Installing the device in the rack on page 32 4. Attaching the rear brackets to the extensions on page 33 5. Attaching the rear brackets to the rack posts on page 34 Attaching the front brackets Complete the following steps to attach the front brackets to the device. 1. Position the right front bracket with the flat side against the right side of the device at the front of the device, as shown in Figure 4 . 2. Insert four 8-32 x 5/16-in. flathead screws through the vertically aligned holes in the bracket and then into the holes on the side of the device. Use the upper and lower screw holes, leaving the center holes empty. 3. Repeat step 1 and step 2 to attach the left front bracket to the left side of the device. 4. Tighten all the 8-32 x 5/16-in. screws to a torque of 15 in-lb (17 cm-kg). 30 Brocade G620 Hardware Installation Guide 53-1003990-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Flush-front mounting
CAUTION
The device must be turned off and disconnected from the fabric during this procedure.
NOTE
The illustrations in the rack installation procedures show a 1U device, but the instructions are the
same for a 2U device. The illustrations in the rack installation procedures are for reference only and
may not show the actual device.
Complete the following tasks to install the device in a four-post rack:
1.
Attaching the front brackets
on page 30
2.
Attaching the extension brackets to the device
on page 31
3.
Installing the device in the rack
on page 32
4.
Attaching the rear brackets to the extensions
on page 33
5.
Attaching the rear brackets to the rack posts
on page 34
Attaching the front brackets
Complete the following steps to attach the front brackets to the device.
1.
Position the right front bracket with the flat side against the right side of the device at the front of the
device, as shown in
Figure 4
.
2.
Insert four 8-32 x 5/16-in. flathead screws through the vertically aligned holes in the bracket and
then into the holes on the side of the device. Use the upper and lower screw holes, leaving the
center holes empty.
3.
Repeat step 1 and step 2 to attach the left front bracket to the left side of the device.
4.
Tighten all the 8-32 x 5/16-in. screws to a torque of 15 in-lb (17 cm-kg).
Flush-front mounting
30
Brocade G620 Hardware Installation Guide
53-1003990-01