Dell Brocade G620 Hardware Installation Guide - Page 36

Attaching the front brackets to the rear of the device

Get Dell Brocade G620 PDF manuals and user guides View all Dell Brocade G620 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Attaching the front brackets to the rear of the device Attaching the front brackets to the rear of the device NOTE In this installation, the brackets are named as listed in the parts list even though the installation of the brackets is reversed from the flush-front installation. Complete the following steps to attach the front brackets to the rear of the device. 1. Position the right front bracket with the flat side against the right rear side of the device, as shown in Figure 9 . 2. Insert four 8-32 x 5/16-in. flathead screws through the vertically aligned holes in the bracket and then into the holes on the side of the device. Use the upper and lower screw holes, leaving the center holes empty. 3. Repeat step 1 and step 2 to attach the left rear bracket to the left side of the device. 4. Tighten all the 8-32 x 5/16-in. screws to a torque of 15 in-lb (17 cm-kg). 1 The Brocade device 2 Screws, 8-32 x 5/16-in., flathead Phillips 3 Front brackets FIGURE 9 Attaching the front brackets to the rear of the device Attaching the extensions to the front of the device Complete the following steps to attach the extension brackets to the front of the device. There are medium and long extension brackets that you can use for this step. Choose the correct extension for the depth of your rack. 1. Select the proper length extension bracket for your rack depth. 2. Position the right extension along the side of the device as shown in Figure 10 . 36 Brocade G620 Hardware Installation Guide 53-1003990-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Attaching the front brackets to the rear of the device
NOTE
In this installation, the brackets are named as listed in the parts list even though the installation of the
brackets is reversed from the flush-front installation.
Complete the following steps to attach the front brackets to the rear of the device.
1.
Position the right front bracket with the flat side against the right rear side of the device, as shown in
Figure 9
.
2.
Insert four 8-32 x 5/16-in. flathead screws through the vertically aligned holes in the bracket and
then into the holes on the side of the device. Use the upper and lower screw holes, leaving the
center holes empty.
3.
Repeat step 1 and step 2 to attach the left rear bracket to the left side of the device.
4.
Tighten all the 8-32 x 5/16-in. screws to a torque of 15 in-lb (17 cm-kg).
1
The Brocade device
2
Screws, 8-32 x 5/16-in., flathead
Phillips
3
Front brackets
FIGURE 9
Attaching the front brackets to the rear of the device
Attaching the extensions to the front of the device
Complete the following steps to attach the extension brackets to the front of the device. There are
medium and long extension brackets that you can use for this step. Choose the correct extension for
the depth of your rack.
1.
Select the proper length extension bracket for your rack depth.
2.
Position the right extension along the side of the device as shown in
Figure 10
.
Attaching the front brackets to the rear of the device
36
Brocade G620 Hardware Installation Guide
53-1003990-01