Dell Brocade G620 Hardware Installation Guide - Page 37

Dell Brocade G620 Manual

Get Dell Brocade G620 PDF manuals and user guides View all Dell Brocade G620 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Installing the device in the rack 3. Attach the bracket using four 8-32 x 5/16-in. flathead screws. 4. Repeat step 1 and step 2 to attach the left front extension to the left side of the device. 5. Tighten all the 8-32 x 5/16-in. screws to a torque of 15 in-lb (17 cm-kg). 1 Extension brackets 2 Screws, 8-32 x 5/16-in., flathead Phillips FIGURE 10 Attaching the bracket extensions to the device Installing the device in the rack Complete the following steps to install the device in the rack. 1. Position the device in the rack, as shown in Figure 11 , providing temporary support under the device until the rail kit is secured to the rack. 2. Attach the right front bracket to the right rear rack post using two 10-32 x 5/8-in. panhead screws and two retainer nuts. Use the upper and lower holes in the bracket. 3. Attach the left front bracket to the left rear rack post using two 10-32 x 5/8-in. panhead screws and two retainer nuts. Use the upper and lower holes in the bracket. 4. Tighten all the 10-32 x 5/8-in. screws to a torque of 25 in-lb (29 cm-kg). Brocade G620 Hardware Installation Guide 37 53-1003990-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
3.
Attach the bracket using four 8-32 x 5/16-in. flathead screws.
4.
Repeat step 1 and step 2 to attach the left front extension to the left side of the device.
5.
Tighten all the 8-32 x 5/16-in. screws to a torque of 15 in-lb (17 cm-kg).
1
Extension brackets
2
Screws, 8-32 x 5/16-in., flathead
Phillips
FIGURE 10
Attaching the bracket extensions to the device
Installing the device in the rack
Complete the following steps to install the device in the rack.
1.
Position the device in the rack, as shown in
Figure 11
, providing temporary support under the device
until the rail kit is secured to the rack.
2.
Attach the right front bracket to the right rear rack post using two 10-32 x 5/8-in. panhead screws and
two retainer nuts. Use the upper and lower holes in the bracket.
3.
Attach the left front bracket to the left rear rack post using two 10-32 x 5/8-in. panhead screws and
two retainer nuts. Use the upper and lower holes in the bracket.
4.
Tighten all the 10-32 x 5/8-in. screws to a torque of 25 in-lb (29 cm-kg).
Installing the device in the rack
Brocade G620 Hardware Installation Guide
37
53-1003990-01