Dell Brocade G620 Hardware Installation Guide - Page 40

Attaching the rear brackets to the front rack posts, Installing the Universal Two-Post Rack kit (XBR

Get Dell Brocade G620 PDF manuals and user guides View all Dell Brocade G620 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Attaching the rear brackets to the front rack posts FIGURE 13 Attaching the short or long rear brackets to the extensions Attaching the rear brackets to the front rack posts Complete the following steps to attach the rear brackets to the front rack posts. 1. Attach the right rear bracket to the right front rack post using two 10-32 x 5/8-in. screws and two retainer nuts, as shown in Figure 14 . Use the upper and lower holes in the bracket. 2. Attach the left rear bracket to the left front rack post using two 10-32 x 5/8-in. screws and two retainer nuts. Use the upper and lower holes in the bracket. 3. Tighten all the 10-32 x 5/8-in. screws to a torque of 25 in-lb (29 cm-kg). 1 Screws, 10-32 x 5/8-in., panhead Phillips 2 Retainer nuts, 10-32 FIGURE 14 Attaching the rear brackets to the front rack posts Installing the Universal Two-Post Rack kit (XBR-R000294) Use the following instructions to install a Brocade 1U or 2U switch in a two-post telecommunications (Telco) rack using the Universal Two-Post Rack Kit (XBR-R000294). There are two ways you can mount the device in a two-post rack: • With the port side flush with the front posts • With the posts mounted to the midsection of the device 40 Brocade G620 Hardware Installation Guide 53-1003990-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
FIGURE 13
Attaching the short or long rear brackets to the extensions
Attaching the rear brackets to the front rack posts
Complete the following steps to attach the rear brackets to the front rack posts.
1.
Attach the right rear bracket to the right front rack post using two 10-32 x 5/8-in. screws and two
retainer nuts, as shown in
Figure 14
. Use the upper and lower holes in the bracket.
2.
Attach the left rear bracket to the left front rack post using two 10-32 x 5/8-in. screws and two
retainer nuts. Use the upper and lower holes in the bracket.
3.
Tighten all the 10-32 x 5/8-in. screws to a torque of 25 in-lb (29 cm-kg).
1
Screws, 10-32 x 5/8-in., panhead
Phillips
2
Retainer nuts, 10-32
FIGURE 14
Attaching the rear brackets to the front rack posts
Installing the Universal Two-Post Rack kit (XBR-R000294)
Use the following instructions to install a Brocade 1U or 2U switch in a two-post telecommunications
(Telco) rack using the
Universal Two-Post Rack Kit (XBR-R000294).
There are two ways you can mount the device in a two-post rack:
•
With the port side flush with the front posts
•
With the posts mounted to the midsection of the device
Attaching the rear brackets to the front rack posts
40
Brocade G620 Hardware Installation Guide
53-1003990-01