Dell Brocade G620 Hardware Installation Guide - Page 46

Mid-mounting, Attaching the front brackets to the device

Get Dell Brocade G620 PDF manuals and user guides View all Dell Brocade G620 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Mid-mounting 1 Screws, 8-32 x 5/16-in., panhead Phillips FIGURE 19 Attaching the rear brackets to the device Mid-mounting Observe the following notes when using this procedure: • The device must be turned off and disconnected from the fabric during this procedure. • The illustrations in this document show a 1U device, but the instructions are the same for a 2U device. • The illustrations in the rack installation procedures are for reference only and may not show the actual device. Complete the following tasks to install the device in a rack: 1. Attaching the front brackets to the device on page 46 2. Attaching the front brackets to the rack on page 47 3. Attaching the rear brackets to the rack on page 48 4. Attaching the rear brackets to the device on page 49 Attaching the front brackets to the device Complete the following steps to attach the front brackets to the device. 1. Position the right front bracket with the flat side against the right side of the device, as shown in Figure 20 . 2. Insert four 8-32 x 5/16-in. flathead screws through the vertically aligned holes in the bracket and then into the holes on the side of the device. Use the upper and lower screw holes, leaving the center holes empty. 46 Brocade G620 Hardware Installation Guide 53-1003990-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
1
Screws, 8-32 x 5/16-in., panhead
Phillips
FIGURE 19
Attaching the rear brackets to the device
Mid-mounting
Observe the following notes when using this procedure:
•
The device must be turned off and disconnected from the fabric during this procedure.
•
The illustrations in this document show a 1U device, but the instructions are the same for a 2U
device.
•
The illustrations in the rack installation procedures are for reference only and may not show the
actual device.
Complete the following tasks to install the device in a rack:
1.
Attaching the front brackets to the device
on page 46
2.
Attaching the front brackets to the rack
on page 47
3.
Attaching the rear brackets to the rack
on page 48
4.
Attaching the rear brackets to the device
on page 49
Attaching the front brackets to the device
Complete the following steps to attach the front brackets to the device.
1.
Position the right front bracket with the flat side against the right side of the device, as shown in
Figure 20
.
2.
Insert four 8-32 x 5/16-in. flathead screws through the vertically aligned holes in the bracket and
then into the holes on the side of the device. Use the upper and lower screw holes, leaving the
center holes empty.
Mid-mounting
46
Brocade G620 Hardware Installation Guide
53-1003990-01