Dell Brocade G620 Hardware Installation Guide - Page 44

Attaching the rear brackets to the rack,

Get Dell Brocade G620 PDF manuals and user guides View all Dell Brocade G620 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Attaching the rear brackets to the rack 1. Position the device in the rack, as shown in (Figure 17 ), providing temporary support under the device until the rack kit is fully secured to the rack. 2. Attach the right front bracket to the right rack upright using two 10-32 x 5/8-in. panhead screws and two retainer nuts. Use the upper and lower holes in the bracket. 3. Attach the left front bracket to the left rack upright using two 10-32 x 5/8-in. panhead screws and two retainer nuts. 4. Use the upper and lower holes in the bracket. Tighten all the 10-32 x 5/8-in. screws to a torque of 25 in-lb. (29 cm-kg). 1 Screws, 10-32 x 5/8-in., panhead Phillips 2 Retainer nuts, 10-32 FIGURE 17 Attaching front brackets to a rack Attaching the rear brackets to the rack Complete the following steps to attach the rear brackets to the rack. 1. Select the proper length bracket for your post width. If your posts are three to five inches wide, use the brackets marked 3-5 INCH. If your posts are five to six inches wide, use the brackets marked 5-6 INCH. 2. Position the right rear bracket in the right rear of the device, as shown in Figure 18 . 3. Attach the bracket to the right rack upright using two 10-32 x 5/8-in. panhead screws and two retainer nuts. Use the upper and lower holes in the bracket. 4. Repeat step 2 and step 3 to attach the left rear bracket to the left rack upright. 5. Tighten all the 10-32 x 5/8-in. screws to a torque of 25 in-lb. (29 cm-kg). 44 Brocade G620 Hardware Installation Guide 53-1003990-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
1.
Position the device in the rack, as shown in (
Figure 17
), providing temporary support under the
device until the rack kit is fully secured to the rack.
2.
Attach the right front bracket to the right rack upright using two 10-32 x 5/8-in. panhead screws and
two retainer nuts. Use the upper and lower holes in the bracket.
3.
Attach the left front bracket to the left rack upright using two 10-32 x 5/8-in. panhead screws and
two retainer nuts.
4.
Use the upper and lower holes in the bracket. Tighten all the 10-32 x 5/8-in. screws to a torque of
25 in-lb. (29 cm-kg).
1
Screws, 10-32 x 5/8-in., panhead
Phillips
2
Retainer nuts, 10-32
FIGURE 17
Attaching front brackets to a rack
Attaching the rear brackets to the rack
Complete the following steps to attach the rear brackets to the rack.
1.
Select the proper length bracket for your post width. If your posts are three to five inches wide, use
the brackets marked 3-5 INCH. If your posts are five to six inches wide, use the brackets marked
5-6 INCH.
2.
Position the right rear bracket in the right rear of the device, as shown in
Figure 18
.
3.
Attach the bracket to the right rack upright using two 10-32 x 5/8-in. panhead screws and two
retainer nuts. Use the upper and lower holes in the bracket.
4.
Repeat step 2 and step 3 to attach the left rear bracket to the left rack upright.
5.
Tighten all the 10-32 x 5/8-in. screws to a torque of 25 in-lb. (29 cm-kg).
Attaching the rear brackets to the rack
44
Brocade G620 Hardware Installation Guide
53-1003990-01