Dell Brocade G620 Hardware Installation Guide - Page 35

Flush-rear (recessed) mounting

Get Dell Brocade G620 PDF manuals and user guides View all Dell Brocade G620 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Flush-rear (recessed) mounting 1 Screws, 10-32 x 5/8-in., panhead Phillips 2 Retainer nuts, 10-32 FIGURE 8 Attaching the rear brackets to the rack posts Flush-rear (recessed) mounting The flush-rear (recessed) mounting is similar to the flush-front mounting except that the brackets are reversed on the device. CAUTION The device must be turned off and disconnected from the fabric during this procedure. NOTE The illustrations in the rack installation procedures show a 1U device, but the instructions are the same for a 2U device. The illustrations in the rack installation procedures are for reference only and may not show the actual device. Complete the following tasks to install the device in a four-post rack: 1. Attaching the front brackets to the rear of the device on page 36 2. Attaching the extensions to the front of the device on page 36 3. Installing the device in the rack on page 37 4. Attaching the rear brackets to the extensions at the front of the device on page 38 5. Attaching the rear brackets to the front rack posts on page 40 Brocade G620 Hardware Installation Guide 35 53-1003990-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
1
Screws, 10-32 x 5/8-in., panhead
Phillips
2
Retainer nuts, 10-32
FIGURE 8
Attaching the rear brackets to the rack posts
Flush-rear (recessed) mounting
The flush-rear (recessed) mounting is similar to the flush-front mounting except that the brackets are
reversed on the device.
CAUTION
The device must be turned off and disconnected from the fabric during this procedure.
NOTE
The illustrations in the rack installation procedures show a 1U device, but the instructions are the same
for a 2U device. The illustrations in the rack installation procedures are for reference only and may not
show the actual device.
Complete the following tasks to install the device in a four-post rack:
1.
Attaching the front brackets to the rear of the device
on page 36
2.
Attaching the extensions to the front of the device
on page 36
3.
Installing the device in the rack
on page 37
4.
Attaching the rear brackets to the extensions at the front of the device
on page 38
5.
Attaching the rear brackets to the front rack posts
on page 40
Flush-rear (recessed) mounting
Brocade G620 Hardware Installation Guide
35
53-1003990-01