Dell OptiPlex GX1 Dell OptiPlex GX1/GX1p Managed PC and OptiPlex NX1 Net PC S - Page 105

Remove the four screws attaching the 5.25-inch drive to the mounting

Get Dell OptiPlex GX1 PDF manuals and user guides View all Dell OptiPlex GX1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 105 highlights

retaining tabs (2) To remove a 5.25-inch drive assembly from the middle or lower drive bay, follow these steps: 1. Disconnect the DC power cable and the interface cable from the back of the drive. 2. Press in on the two retaining tabs (one on each side of the drive), and slide the drive assembly forward to remove it. 3. Remove the four screws attaching the 5.25-inch drive to the mounting plate, and lift the drive out of the mounting plate (see Figure 5-10). Align the front of the drive flush with the tab at the front of the 5.25-inch drive-mounting plate. drive-mounting screws (4) When you replace the 5.25-inch drive, align the front of the drive flush with the tab at the front of the mounting plate. Insert the four screws, and tighten them in the order stamped on the bottom of the 5.25-inch drive-mounting plate. Removing and Replacing Parts on the Midsize Chassis 5-11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
Removing and Replacing Parts on the Midsize Chassis
5-11
¸·¹¸´,QFK±’ULYH±$VVHPEO\
)LJXUH±¸´Á³±±¸³µ¸´,QFK±’ULYH±$VVHPEO\±5HPRYDO
To remove a 5.25-inch drive assembly from the middle or lower drive bay, fol-
low these steps:
1.
Disconnect the DC power cable and the interface cable from the back of
the drive.
2.
Press in on the two retaining tabs (one on each side of the drive), and slide
the drive assembly forward to remove it.
3.
Remove the four screws attaching the 5.25-inch drive to the mounting
plate, and lift the drive out of the mounting plate (see Figure 5-10).
)LJXUH±¸´²Â³±±¸³µ¸´,QFK±’ULYH±5HPRYDO
When you replace the 5.25-inch drive, align the front of the drive flush with the
tab at the front of the mounting plate. Insert the four screws, and tighten them
in the order stamped on the bottom of the 5.25-inch drive-mounting plate.
retaining tabs (2)
Align the front of the drive
flush with the tab at the
front of the 5.25-inch
drive-mounting plate.
drive-mounting screws (4)