Dell OptiPlex GX1 Dell OptiPlex GX1/GX1p Managed PC and OptiPlex NX1 Net PC S - Page 106

When you reinstall the hard-disk drive bracket, place the lower-back tab of

Get Dell OptiPlex GX1 PDF manuals and user guides View all Dell OptiPlex GX1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 106 highlights

lower-back tab hard-disk drive bracket handle screw To remove the hard-disk drive bracket, follow these steps. 1. Disconnect the DC power cable and the interface cable from the back of each hard-disk drive installed in the hard-disk drive bracket. 2. Remove the screw that secures the hard-disk drive bracket to the front of the chassis. 3. Grasp the handle on the front of the bracket, and rotate the front of the bracket up until the hooks are free from the chassis. 4. Lift the hard-disk drive bracket out of the computer. When you reinstall the hard-disk drive bracket, place the lower-back tab of the hard-disk drive bracket into position (be sure that the opening in the lower-back tab is over the alignment tab on the chassis); then rotate the front of the bracket down into position. 5-12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
5-12
’HOO±2SWL3OH[±*;²³*;²S±0DQDJHG±3&±DQG±2SWL3OH[±1;²±1HW±3&±6\VWHPV±6HUYLFH±0DQXDO
+DUG´’LVN±’ULYH±%UDFNHW
)LJXUH±¸´²²³±±+DUG´’LVN±’ULYH±%UDFNHW±5HPRYDO±±±
To remove the hard-disk drive bracket, follow these steps.
&$87,21±²7KH²YLGHR²PHPRU\²PRGXOH²FDQ²EH²GDPDJHG²ZKHQ²WKH²
KDUG´GLVN²GULYH²EUDFNHW²LV²UHPRYHG²LI²WKH²KDUG´GLVN²GULYH•V²’&²SRZHU²
FDEOH²DQG²WKH²LQWHUIDFH²FDEOH²DUH²QRW²GLVFRQQHFWHG²ILUVW³²
1.
Disconnect the DC power cable and the interface cable from the back of
each hard-disk drive installed in the hard-disk drive bracket.
2.
Remove the screw that secures the hard-disk drive bracket to the front of
the chassis.
3.
Grasp the handle on the front of the bracket, and rotate the front of the
bracket up until the hooks are free from the chassis.
4.
Lift the hard-disk drive bracket out of the computer.
When you reinstall the hard-disk drive bracket, place the lower-back tab of the
hard-disk drive bracket into position (be sure that the opening in the lower-back
tab is over the alignment tab on the chassis); then rotate the front of the
bracket down into position.
handle
screw
lower-back tab
hard-disk drive
bracket