Dell PowerEdge R240 EMC PowerEdge R240 Installation and Service Manual - Page 54

Intrusion switch, Removing the intrusion switch

Get Dell PowerEdge R240 PDF manuals and user guides View all Dell PowerEdge R240 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Next steps 1. Enter System Setup and ensure that the controller of the drive is enabled. 2. Exit System Setup and reboot the system. 3. Install any software required for the drive operation as described in the documentation for the drive. 4. Follow the procedure listed in the After working inside your system. Intrusion switch Removing the intrusion switch Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. Keep the plastic scribe ready. Steps 1. Disconnect and remove the intrusion switch cable connector from the connector on the system board. NOTE: Observe the routing of the cable as you remove it from the system. Route the cable properly when you replace it to prevent the cable from being pinched or crimped. 2. Using a plastic scribe, slide the intrusion switch out of the intrusion switch slot. Figure 33. Removing the intrusion switch Next steps 1. Replace the intrusion switch. Installing the intrusion switch Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. Steps 1. Align and slide the intrusion switch into the slot in the system. 2. Route the intrusion switch cable through the cable routing clips. 3. Connect the intrusion switch cable connector to the connector on the system board. 54 PowerEdge R240 installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
Next steps
1.
Enter System Setup and ensure that the controller of the drive is enabled.
2.
Exit System Setup and reboot the system.
3.
Install any software required for the drive operation as described in the documentation for the drive.
4.
Follow the procedure listed in the
After working inside your system
.
Intrusion switch
Removing the intrusion switch
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
Keep the plastic scribe ready.
Steps
1.
Disconnect and remove the intrusion switch cable connector from the connector on the system board.
NOTE:
Observe the routing of the cable as you remove it from the system. Route the cable properly when you
replace it to prevent the cable from being pinched or crimped.
2.
Using a plastic scribe, slide the intrusion switch out of the intrusion switch slot.
Figure 33. Removing the intrusion switch
Next steps
1.
Replace the intrusion switch
.
Installing the intrusion switch
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
Steps
1.
Align and slide the intrusion switch into the slot in the system.
2.
Route the intrusion switch cable through the cable routing clips.
3.
Connect the intrusion switch cable connector to the connector on the system board.
54
PowerEdge R240 installing and removing system components