Dell PowerEdge R240 EMC PowerEdge R240 Installation and Service Manual - Page 65

Dell PowerEdge R240 Manual

Get Dell PowerEdge R240 PDF manuals and user guides View all Dell PowerEdge R240 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

NOTE: For instructions, see the documentation accompanying the card. 4. Remove the air shroud. 5. Remove the expansion card riser. Steps 1. Remove the filler bracket. NOTE: Store the filler bracket for future use. Filler brackets must be installed in empty expansion card slots to maintain Federal Communications Commission (FCC) certification of the system. The brackets also keep dust and dirt out of the system and aid in proper cooling and airflow inside the system. Figure 45. Removing expansion card filler 2. Holding the card by its edges, insert the expansion card to connect it to the connector on the riser. Figure 46. Installing expansion card into the expansion card riser Next steps 1. Replace the expansion card riser. 2. Install the air shroud. 3. Follow the procedure listed in the After working inside your system. PowerEdge R240 installing and removing system components 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
NOTE:
For instructions, see the documentation accompanying the card.
4.
Remove the air shroud
.
5.
Remove the expansion card riser
.
Steps
1.
Remove the filler bracket.
NOTE:
Store the filler bracket for future use. Filler brackets must be installed in empty expansion card slots to
maintain Federal Communications Commission (FCC) certification of the system. The brackets also keep dust and
dirt out of the system and aid in proper cooling and airflow inside the system.
Figure 45. Removing expansion card filler
2.
Holding the card by its edges, insert the expansion card to connect it to the connector on the riser.
Figure 46. Installing expansion card into the expansion card riser
Next steps
1.
Replace the expansion card riser
.
2.
Install the air shroud
.
3.
Follow the procedure listed in the
After working inside your system
.
PowerEdge R240 installing and removing system components
65