Dell PowerEdge R240 EMC PowerEdge R240 Installation and Service Manual - Page 69

Optional internal USB memory key, Replacing the optional internal USB memory key

Get Dell PowerEdge R240 PDF manuals and user guides View all Dell PowerEdge R240 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

Figure 50. Installing system battery Next steps 1. Install the expansion card riser. 2. Install the air shroud. 3. Follow the procedure listed in the After working inside your system. 4. Confirm that the battery is operating properly, by performing the following steps: a. Enter the System Setup, while booting, by pressing F2. b. Enter the correct time and date in the System Setup Time and Date fields. c. Exit the System Setup. d. To test the newly installed battery, remove the system from the enclosure for at least an hour. e. Reinstall the system into the enclosure after an hour. f. Enter the System Setup and if the time and date are still incorrect, see Getting help section. Optional internal USB memory key NOTE: To locate the internal USB port on the system board, see the System board jumpers and connectors section. Replacing the optional internal USB memory key Prerequisites CAUTION: To avoid interference with other components in the server, the maximum permissible dimensions of the USB memory key: 15.9 mm width x 57.15 mm length x 7.9 mm height. 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. Remove the expansion card riser. Steps 1. Locate the USB port or USB memory key on the system board. PowerEdge R240 installing and removing system components 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
Figure 50. Installing system battery
Next steps
1.
Install the expansion card riser
.
2.
Install the air shroud
.
3.
Follow the procedure listed in the
After working inside your system
.
4.
Confirm that the battery is operating properly, by performing the following steps:
a.
Enter the System Setup, while booting, by pressing
F2
.
b.
Enter the correct time and date in the System Setup
Time
and
Date
fields.
c.
Exit
the System Setup.
d.
To test the newly installed battery, remove the system from the enclosure for at least an hour.
e.
Reinstall the system into the enclosure after an hour.
f.
Enter the System Setup and if the time and date are still incorrect, see
Getting help
section.
Optional internal USB memory key
NOTE:
To locate the internal USB port on the system board, see the
System board jumpers and connectors
section.
Replacing the optional internal USB memory key
Prerequisites
CAUTION:
To avoid interference with other components in the server, the maximum permissible dimensions of the USB
memory key: 15.9 mm width x 57.15 mm length x 7.9 mm height.
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
Remove the expansion card riser
.
Steps
1.
Locate the USB port or USB memory key on the system board.
PowerEdge R240 installing and removing system components
69