Dell PowerEdge R240 EMC PowerEdge R240 Installation and Service Manual - Page 76

Removing the MicroSD card

Get Dell PowerEdge R240 PDF manuals and user guides View all Dell PowerEdge R240 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

Next steps 1. Install the MicroSD cards. NOTE: Reinstall the MicroSD cards into the same slots that are based on the labels you had marked on the cards during removal. 2. Install the air shroud. 3. Follow the procedure that is listed in After working inside your system. Removing the MicroSD card Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. Remove the air shroud. 4. Remove the IDSDM or vFlash module. Steps 1. Locate the MicroSD card slot on the vFlash/IDSDM module, and press the card to partially release it from the slot. To locate IDSDM/ vFlash module, see the System board jumpers and connectors section. 2. Hold the MicroSD card and remove it from the slot. NOTE: Temporarily label each MicroSD card with its corresponding slot number after removal. Figure 58. Removing the MicroSD card Next steps 1. Replace the MicroSD cards. 76 PowerEdge R240 installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
Next steps
1.
Install the MicroSD cards.
NOTE:
Reinstall the MicroSD cards into the same slots that are based on the labels you had marked on the cards
during removal.
2.
Install the air shroud
.
3.
Follow the procedure that is listed in
After working inside your system
.
Removing the MicroSD card
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
Remove the air shroud.
4.
Remove the IDSDM or vFlash module.
Steps
1.
Locate the MicroSD card slot on the vFlash/IDSDM module, and press the card to partially release it from the slot. To locate IDSDM/
vFlash module, see the
System board jumpers and connectors
section.
2.
Hold the MicroSD card and remove it from the slot.
NOTE:
Temporarily label each MicroSD card with its corresponding slot number after removal.
Figure 58. Removing the MicroSD card
Next steps
1.
Replace the MicroSD cards.
76
PowerEdge R240 installing and removing system components