Dell PowerEdge R240 EMC PowerEdge R240 Installation and Service Manual - Page 70

Optional optical drive, Removing the optional optical drive

Get Dell PowerEdge R240 PDF manuals and user guides View all Dell PowerEdge R240 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

To locate the USB port, see the System board jumpers and connectors section. 2. If installed, remove the USB memory key from the USB port. 3. Insert the replacement USB memory key into the USB port. Next steps 1. Replace the expansion card riser. 2. Follow the procedure that is listed in After working inside your system. 3. While booting, press F2 to enter System Setup and verify that the system detects the USB memory key. Optional optical drive Removing the optional optical drive Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. Remove the front bezel. 4. Remove the air shroud. 5. Disconnect the cables from the connectors on the optical drive. NOTE: Ensure that you note the routing of the power and data cable on the side of the system as you remove them from the system board and drive. Steps 1. Press the release tab to release the optical drive from the system. 2. Slide the optical drive out of the system until it is free of the optical drive slot. 3. If you are not installing a new optical drive, install the optical drive blank. NOTE: The procedure to install an optical blank is similar to the optical drive. Figure 51. Removing the optional optical drive Next steps 1. If applicable, replace the optical drive. 70 PowerEdge R240 installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
To locate the USB port, see the
System board jumpers and connectors
section.
2.
If installed, remove the USB memory key from the USB port.
3.
Insert the replacement USB memory key into the USB port.
Next steps
1.
Replace the expansion card riser
.
2.
Follow the procedure that is listed in
After working inside your system
.
3.
While booting, press F2 to enter System Setup and verify that the system detects the USB memory key.
Optional optical drive
Removing the optional optical drive
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
Remove the front bezel
.
4.
Remove the air shroud
.
5.
Disconnect the cables from the connectors on the optical drive.
NOTE:
Ensure that you note the routing of the power and data cable on the side of the system as you remove them
from the system board and drive.
Steps
1.
Press the release tab to release the optical drive from the system.
2.
Slide the optical drive out of the system until it is free of the optical drive slot.
3.
If you are not installing a new optical drive, install the optical drive blank.
NOTE:
The procedure to install an optical blank is similar to the optical drive.
Figure 51. Removing the optional optical drive
Next steps
1.
If applicable,
replace the optical drive.
70
PowerEdge R240 installing and removing system components