Dell PowerEdge R240 EMC PowerEdge R240 Installation and Service Manual - Page 71

Installing the optional optical drive, Processor and heat sink, Removing the heat sink

Get Dell PowerEdge R240 PDF manuals and user guides View all Dell PowerEdge R240 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

Installing the optional optical drive Prerequisites The procedure for installing an optical drive and optical drive blank. 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. Remove the front bezel. 4. Remove the air shroud. 5. If installed, remove the optical drive blank. NOTE: The procedure to remove the optical drive blank and the optical drive is similar. Steps 1. Align and slide the optical drive into the slot until the release tab snaps into place. 2. Connect the power and data cables to the connectors on the optical drive. NOTE: Route the cables properly to prevent them from being pinched or crimped. Figure 52. Installing the optional optical drive Next steps 1. Install the front bezel. 2. Follow the procedure listed in the After working inside your system. Processor and heat sink Removing the heat sink Prerequisites WARNING: The heat sink may be hot to touch for some time after the system is powered down. Allow the heat sink to cool before removing it. 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. Remove the air shroud. 4. Remove the expansion card riser. Steps 1. Using a Philips #2 screwdriver, loosen the screws on the heat sink in the order mentioned below: PowerEdge R240 installing and removing system components 71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
Installing the optional optical drive
Prerequisites
The procedure for installing an optical drive and optical drive blank.
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
Remove the front bezel
.
4.
Remove the air shroud
.
5.
If installed, remove the optical drive blank.
NOTE:
The procedure to remove the optical drive blank and the optical drive is similar.
Steps
1.
Align and slide the optical drive into the slot until the release tab snaps into place.
2.
Connect the power and data cables to the connectors on the optical drive.
NOTE:
Route the cables properly to prevent them from being pinched or crimped.
Figure 52. Installing the optional optical drive
Next steps
1.
Install the front bezel.
2.
Follow the procedure listed in the
After working inside your system
.
Processor and heat sink
Removing the heat sink
Prerequisites
WARNING:
The heat sink may be hot to touch for some time after the system is powered down. Allow the heat sink to
cool before removing it.
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
Remove the air shroud
.
4.
Remove the expansion card riser
.
Steps
1.
Using a Philips #2 screwdriver, loosen the screws on the heat sink in the order mentioned below:
PowerEdge R240 installing and removing system components
71