Dell PowerEdge R240 EMC PowerEdge R240 Installation and Service Manual - Page 92

Removing the right control panel

Get Dell PowerEdge R240 PDF manuals and user guides View all Dell PowerEdge R240 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

Figure 76. Installing the left control panel Next steps 1. Follow the procedure listed in the After working inside your system. Removing the right control panel Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. If applicable, remove the front bezel. 4. Remove the air shroud. Steps 1. Disconnect the control panel cable from the system board connector. NOTE: Ensure that you note the routing of the cables as you remove them from the system board. 2. Using the appropriate screwdriver, remove the screws that secure the right control panel assembly to the system. 3. Holding the control panel assembly, remove the control panel from the system. 92 PowerEdge R240 installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
Figure 76. Installing the left control panel
Next steps
1.
Follow the procedure listed in the
After working inside your system
.
Removing the right control panel
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
If applicable,
remove the front bezel
.
4.
Remove the air shroud
.
Steps
1.
Disconnect the control panel cable from the system board connector.
NOTE:
Ensure that you note the routing of the cables as you remove them from the system board.
2.
Using the appropriate screwdriver, remove the screws that secure the right control panel assembly to the system.
3.
Holding the control panel assembly, remove the control panel from the system.
92
PowerEdge R240 installing and removing system components