Dell PowerEdge R240 EMC PowerEdge R240 Installation and Service Manual - Page 75

Removing the optional IDSDM or vFlash card, Installing optional IDSDM or vFlash card

Get Dell PowerEdge R240 PDF manuals and user guides View all Dell PowerEdge R240 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

Removing the optional IDSDM or vFlash card Prerequisites 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure listed in Before working inside your system. 3. Remove the air shroud. 4. If you are replacing the IDSDM/vFlash card, remove the MicroSD cards. NOTE: Temporarily label each SD card with its corresponding slot number before removal. Reinstall the SD cards into the corresponding slots. Steps Holding the pull tab, lift the IDSDM/vFlash card out of the system. Next steps NOTE: If you are replacing the IDSDM or vFlash module, remove the MicroSD cards. 1. Replace the IDSDM/vFlash module. Installing optional IDSDM or vFlash card Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. Remove the air shroud. Steps 1. Locate the IDSDM/vFlash connector on the system board. To locate IDSDM/vFlash connector, see System board jumpers and connectors section. 2. Align the IDSDM/vFlash card with the connector on the system board. 3. Push the IDSDM/vFlash card until it is firmly seated on the system board. Figure 57. Installing the optional IDSDM or vFlash card PowerEdge R240 installing and removing system components 75

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
Removing the optional IDSDM or vFlash card
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure listed in
Before working inside your system
.
3.
Remove the air shroud.
4.
If you are replacing the IDSDM/vFlash card,
remove the MicroSD cards
.
NOTE:
Temporarily label each SD card with its corresponding slot number before removal. Reinstall the SD cards
into the corresponding slots.
Steps
Holding the pull tab, lift the IDSDM/vFlash card out of the system.
Next steps
NOTE:
If you are replacing the IDSDM or vFlash module, remove the MicroSD cards.
1.
Replace the IDSDM/vFlash module.
Installing optional IDSDM or vFlash card
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
Remove the air shroud.
Steps
1.
Locate the IDSDM/vFlash connector on the system board. To locate IDSDM/vFlash connector, see
System board jumpers and
connectors
section.
2.
Align the IDSDM/vFlash card with the connector on the system board.
3.
Push the IDSDM/vFlash card until it is firmly seated on the system board.
Figure 57. Installing the optional IDSDM or vFlash card
PowerEdge R240 installing and removing system components
75