Dell PowerEdge R240 EMC PowerEdge R240 Installation and Service Manual - Page 67

System battery, Replacing the system battery

Get Dell PowerEdge R240 PDF manuals and user guides View all Dell PowerEdge R240 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Steps 1. Align the M.2 SSD module at an angle with the BOSS card connector. 2. Insert the M.2 SSD module until it is firmly seated in the BOSS card connector. 3. Using the Phillips #1 screwdriver, secure the M.2 SSD module on the BOSS card with the screw. Figure 48. Installing the M.2 SSD module Next steps 1. Install the BOSS card. NOTE: The procedure to install the BOSS card is similar to removing an expansion card. 2. Install the air shroud. 3. Follow the procedure listed in the After working inside your system. System battery Replacing the system battery Prerequisites NOTE: There is a danger of a new battery exploding if it is incorrectly installed. Replace the battery only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions. See the safety instructions that came with your system for more information. 1. Follow the safety guidelines listed in the Safety instructions.. 2. Follow the procedure listed in the Before working inside your system. 3. Remove the air shroud. Steps 1. To remove the battery: a. Push the battery holder clip. PowerEdge R240 installing and removing system components 67

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
Steps
1.
Align the M.2 SSD module at an angle with the BOSS card connector.
2.
Insert the M.2 SSD module until it is firmly seated in the BOSS card connector.
3.
Using the Phillips #1 screwdriver, secure the M.2 SSD module on the BOSS card with the screw.
Figure 48. Installing the M.2 SSD module
Next steps
1.
Install the BOSS card.
NOTE:
The procedure to install the BOSS card is similar to removing an expansion card.
2.
Install the air shroud
.
3.
Follow the procedure listed in the
After working inside your system
.
System battery
Replacing the system battery
Prerequisites
NOTE:
There is a danger of a new battery exploding if it is incorrectly installed. Replace the battery only with the same
or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's
instructions. See the safety instructions that came with your system for more information.
1.
Follow the safety guidelines listed in the
Safety instructions
..
2.
Follow the procedure listed in the
Before working inside your system
.
3.
Remove the air shroud
.
Steps
1.
To remove the battery:
a.
Push the battery holder clip.
PowerEdge R240 installing and removing system components
67