Dell PowerEdge R240 EMC PowerEdge R240 Installation and Service Manual - Page 62

Installing the expansion card riser

Get Dell PowerEdge R240 PDF manuals and user guides View all Dell PowerEdge R240 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

Next steps 1. If applicable, replace the expansion card riser. Installing the expansion card riser Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. Remove the air shroud. 4. Install the expansion card in the expansion card riser. Steps 1. If applicable, remove the expansion card riser filler bracket by performing the following steps: a. Open the blue expansion card retention latch lock. b. Using a Phillips #2 screwdriver, remove the screw securing the expansion card riser filler to the system board. c. Slide the expansion card riser filler bracket up and out of the system. Figure 41. Removing the expansion card riser filler 2. Holding the blue touch points on the expansion card riser, align the expansion card with the connector on the system board. 3. Lower the expansion card riser into place until the expansion card riser is fully seated with the connector on the system board. 4. Close the blue expansion card retention latch. 62 PowerEdge R240 installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
Next steps
1.
If applicable,
replace the expansion card riser
.
Installing the expansion card riser
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
Remove the air shroud
.
4.
Install the expansion card in the expansion card riser
.
Steps
1.
If applicable, remove the expansion card riser filler bracket by performing the following steps:
a.
Open the blue expansion card retention latch lock.
b.
Using a Phillips #2 screwdriver, remove the screw securing the expansion card riser filler to the system board.
c.
Slide the expansion card riser filler bracket up and out of the system.
Figure 41. Removing the expansion card riser filler
2.
Holding the blue touch points on the expansion card riser, align the expansion card with the connector on the system board.
3.
Lower the expansion card riser into place until the expansion card riser is fully seated with the connector on the system board.
4.
Close the blue expansion card retention latch.
62
PowerEdge R240 installing and removing system components