Dell PowerEdge R240 EMC PowerEdge R240 Installation and Service Manual - Page 93

Installing the right control panel

Get Dell PowerEdge R240 PDF manuals and user guides View all Dell PowerEdge R240 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 93 highlights

Figure 77. Removing the right control panel Next steps 1. Install the right control panel. Installing the right control panel Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. Remove the front bezel. 4. Remove the air shroud. Steps 1. Route the control panel cable through the side and the guide slots in the system. NOTE: Route the cable properly to prevent the cable from being pinched or crimped. 2. Align and insert the right control panel assembly in the slot on the system. 3. Connect the control panel cable to the system board connector. 4. Using the appropriate screwdriver, replace the screws that secure the right control panel to the system. PowerEdge R240 installing and removing system components 93

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
Figure 77. Removing the right control panel
Next steps
1.
Install the right control panel
.
Installing the right control panel
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
Remove the front bezel
.
4.
Remove the air shroud
.
Steps
1.
Route the control panel cable through the side and the guide slots in the system.
NOTE:
Route the cable properly to prevent the cable from being pinched or crimped.
2.
Align and insert the right control panel assembly in the slot on the system.
3.
Connect the control panel cable to the system board connector.
4.
Using the appropriate screwdriver, replace the screws that secure the right control panel to the system.
PowerEdge R240 installing and removing system components
93