Dell PowerEdge R240 EMC PowerEdge R240 Installation and Service Manual - Page 83

Installing a cabled power supply unit

Get Dell PowerEdge R240 PDF manuals and user guides View all Dell PowerEdge R240 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

6. If applicable, remove the expansion card riser. Steps 1. Using a Phillips #2 screwdriver, remove the screw securing the PSU to the system. 2. Slide the PSU out of the PSU bay in the chassis. Figure 69. Removing a cabled power supply unit Next steps 1. Replace cabled AC power supply. Installing a cabled power supply unit Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. Remove the air shroud. 4. Remove the expansion card riser. Steps 1. Slide the new PSU into the PSU bay in the chassis until the PSU is fully seated. 2. Using a Phillips #2 screwdriver, replace the screw to secure the PSU to the system. PowerEdge R240 installing and removing system components 83

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
6.
If applicable,
remove the expansion card riser
.
Steps
1.
Using a Phillips #2 screwdriver, remove the screw securing the PSU to the system.
2.
Slide the PSU out of the PSU bay in the chassis.
Figure 69. Removing a cabled power supply unit
Next steps
1.
Replace cabled AC power supply.
Installing a cabled power supply unit
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
Remove the air shroud
.
4.
Remove the expansion card riser
.
Steps
1.
Slide the new PSU into the PSU bay in the chassis until the PSU is fully seated.
2.
Using a Phillips #2 screwdriver, replace the screw to secure the PSU to the system.
PowerEdge R240 installing and removing system components
83