Dell PowerEdge R6525 EMC Installation and Service Manual - Page 110

Optional serial COM port, Removing the serial COM port

Get Dell PowerEdge R6525 PDF manuals and user guides View all Dell PowerEdge R6525 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 110 highlights

NOTE: Push the black card holder to hold the card in the riser. Figure 88. Closing the card holder on the expansion card riser Next steps 1. If applicable, connect the cables to the expansion card. 2. Follow the procedure listed in After working inside your system on page 43. 3. Install any device drivers required for the card as described in the documentation for the card. Optional serial COM port Removing the serial COM port Prerequisites 1. Follow the safety guidelines listed in the Safety instructions on page 42. 2. Follow the procedure listed in the Before working inside your system on page 43. Steps 1. Lift the expansion card riser and disconnect the serial COM port cable from the connector on the rear I/O board. 2. Open the latch on the expansion card riser and slide the serial COM port out of the expansion card riser. NOTE: The numbers on the image do not depict the exact steps. The numbers are for representation of sequence. 110 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
NOTE:
Push the black card holder to hold the card in the riser.
Figure 88. Closing the card holder on the expansion card riser
Next steps
1.
If applicable, connect the cables to the expansion card.
2.
Follow the procedure listed in
After working inside your system
on page 43.
3.
Install any device drivers required for the card as described in the documentation for the card.
Optional serial COM port
Removing the serial COM port
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
on page 42.
2.
Follow the procedure listed in the
Before working inside your system
on page 43.
Steps
1.
Lift the expansion card riser
and disconnect the serial COM port cable from the connector on the rear I/O board.
2.
Open the latch on the expansion card riser and slide the serial COM port out of the expansion card riser.
NOTE:
The numbers on the image do not depict the exact steps. The numbers are for representation of sequence.
110
Installing and removing system components