Dell PowerEdge R6525 EMC Installation and Service Manual - Page 49

Control panel, Removing the right control panel

Get Dell PowerEdge R6525 PDF manuals and user guides View all Dell PowerEdge R6525 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

Next steps 1. Follow the procedure listed in After working inside your system on page 43. Control panel Removing the right control panel Prerequisites 1. Follow the safety guidelines listed in the Safety instructions on page 42. 2. Follow the procedure listed in the Before working inside your system on page 43. 3. Remove the drive backplane cover. 4. If installed, remove the air shroud. Steps 1. Disconnect the right control panel cable from the connector on the system board. 2. Lift the latch, and slide the cable out of the clip. NOTE: Observe the routing of the cable as you remove the right control panel from the system. 3. Using the Phillips #1 screwdriver, remove the screws that secure the right control panel to the system. 4. Holding the cable, slide the right control panel out of the system. NOTE: The numbers on the image do not depict the exact steps. The numbers are for representation of sequence. Figure 21. Removing the right control panel Next steps 1. Replace the right control panel. Installing and removing system components 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
Next steps
1.
Follow the procedure listed in
After working inside your system
on page 43.
Control panel
Removing the right control panel
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
on page 42.
2.
Follow the procedure listed in the
Before working inside your system
on page 43.
3.
Remove the drive backplane cover
.
4.
If installed,
remove the air shroud
.
Steps
1.
Disconnect the right control panel cable from the connector on the system board.
2.
Lift the latch, and slide the cable out of the clip.
NOTE:
Observe the routing of the cable as you remove the right control panel from the system.
3.
Using the Phillips #1 screwdriver, remove the screws that secure the right control panel to the system.
4.
Holding the cable, slide the right control panel out of the system.
NOTE:
The numbers on the image do not depict the exact steps. The numbers are for representation of sequence.
Figure 21. Removing the right control panel
Next steps
1.
Replace the right control panel
.
Installing and removing system components
49