Dell PowerEdge R6525 EMC Installation and Service Manual - Page 79

Installing the rear mounting front PERC module

Get Dell PowerEdge R6525 PDF manuals and user guides View all Dell PowerEdge R6525 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

Figure 61. Removing the rear mounting front PERC module Next steps 1. Replace the rear mounting front PERC module. Installing the rear mounting front PERC module Prerequisites 1. Follow the safety guidelines listed in the Safety instructions on page 42. 2. Follow the procedure listed in Before working inside your system on page 43. 3. Remove the drive backplane cover. 4. If installed, remove the air shroud. 5. Remove the drive backplane. 6. Route the cable properly to prevent the cable from being pinched or crimped. Steps 1. Align the connectors on the front PERC module with the connectors on the drive backplane. 2. Slide the front PERC module until the module is connected to the drive backplane. 3. Using a Phillips #2 screwdriver, tighten the captive screws on the front PERC module. NOTE: The numbers on the image do not depict the exact steps. The numbers are for representation of sequence. Installing and removing system components 79

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
Figure 61. Removing the rear mounting front PERC module
Next steps
1.
Replace the rear mounting front PERC module
.
Installing the rear mounting front PERC module
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
on page 42.
2.
Follow the procedure listed in
Before working inside your system
on page 43.
3.
Remove the drive backplane cover
.
4.
If installed,
remove the air shroud
.
5.
Remove the drive backplane
.
6.
Route the cable properly to prevent the cable from being pinched or crimped.
Steps
1.
Align the connectors on the front PERC module with the connectors on the drive backplane.
2.
Slide the front PERC module until the module is connected to the drive backplane.
3.
Using a Phillips #2 screwdriver, tighten the captive screws on the front PERC module.
NOTE:
The numbers on the image do not depict the exact steps. The numbers are for representation of sequence.
Installing and removing system components
79