Dell PowerEdge R6525 EMC Installation and Service Manual - Page 121

Intrusion switch module, Removing the intrusion switch module

Get Dell PowerEdge R6525 PDF manuals and user guides View all Dell PowerEdge R6525 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 121 highlights

3. Remove the expansion card risers. Steps 1. Connect the USB key to the internal USB card. 2. Align the internal USB card with the connector on the system board and press firmly until the internal USB card is seated. Figure 100. Installing the internal USB card Next steps 1. Install the expansion card risers. 2. Follow the procedure listed in After working inside your system on page 43. 3. While booting, press F2 to enter System Setup and verify that the system detects the USB memory key. Intrusion switch module Removing the intrusion switch module Prerequisites 1. Follow the safety guidelines listed in the Safety instructions on page 42. 2. Follow the procedure listed in the Before working inside your system on page 43. 3. Remove the expansion card riser. NOTE: Ensure that you note the routing of the cables as you remove them from the system board. Route the cable properly when you replace it to prevent the cable from being pinched or crimped Steps 1. Disconnect the intrusion switch cable from the connector on the rear I/O board. 2. Using a Phillips #2 screwdriver, loosen the screw on the intrusion switch module. 3. Slide the intrusion switch module out of the slot on the system. NOTE: The numbers on the image do not depict the exact steps. The numbers are for representation of sequence. Installing and removing system components 121

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
3.
Remove the expansion card risers
.
Steps
1.
Connect the USB key to the internal USB card.
2.
Align the internal USB card with the connector on the system board and press firmly until the internal USB card is seated.
Figure 100. Installing the internal USB card
Next steps
1.
Install the expansion card risers
.
2.
Follow the procedure listed in
After working inside your system
on page 43.
3.
While booting, press F2 to enter
System Setup
and verify that the system detects the USB memory key.
Intrusion switch module
Removing the intrusion switch module
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
on page 42.
2.
Follow the procedure listed in the
Before working inside your system
on page 43.
3.
Remove the expansion card riser
.
NOTE:
Ensure that you note the routing of the cables as you remove them from the system board. Route the cable
properly when you replace it to prevent the cable from being pinched or crimped
Steps
1.
Disconnect the intrusion switch cable from the connector on the rear I/O board.
2.
Using a Phillips #2 screwdriver, loosen the screw on the intrusion switch module.
3.
Slide the intrusion switch module out of the slot on the system.
NOTE:
The numbers on the image do not depict the exact steps. The numbers are for representation of sequence.
Installing and removing system components
121