Dell PowerEdge R6525 EMC Installation and Service Manual - Page 76

Front PERC module, Removing the front mounting front PERC module

Get Dell PowerEdge R6525 PDF manuals and user guides View all Dell PowerEdge R6525 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

Figure 58. Installing the rear drive module Next steps 1. If removed, install the expansion card riser 3. 2. Connect all the cables to the rear drive module. 3. Install the rear drives. 4. Install the air shroud. 5. Follow the procedure listed in After working inside your system. Front PERC module Removing the front mounting front PERC module Prerequisites 1. Follow the safety guidelines listed in the Safety instructions on page 42. 2. Follow the procedure listed in the Before working inside your system on page 43. 3. Remove the drive backplane cover. 4. If installed, remove the air shroud. 5. Disconnect all the cables, observe the cable routing. Steps 1. Using a Phillips #2 screwdriver, loosen the captive screws on the front PERC module. 2. Pull the front PERC module to disengage from the connector on the drive backplane. 3. Tilt and lift the front PERC module out of the system. NOTE: The numbers on the image do not depict the exact steps. The numbers are for representation of sequence. 76 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
Figure 58. Installing the rear drive module
Next steps
1.
If removed,
install the expansion card riser 3.
2.
Connect all the cables to the rear drive module.
3.
Install the rear drives.
4.
Install the air shroud.
5.
Follow the procedure listed in After working inside your system.
Front PERC module
Removing the front mounting front PERC module
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
on page 42.
2.
Follow the procedure listed in the
Before working inside your system
on page 43.
3.
Remove the drive backplane cover
.
4.
If installed,
remove the air shroud
.
5.
Disconnect all the cables, observe the cable routing.
Steps
1.
Using a Phillips #2 screwdriver, loosen the captive screws on the front PERC module.
2.
Pull the front PERC module to disengage from the connector on the drive backplane.
3.
Tilt and lift the front PERC module out of the system.
NOTE:
The numbers on the image do not depict the exact steps. The numbers are for representation of sequence.
76
Installing and removing system components